PIC18LF6310-I/PT Microchip Technology, PIC18LF6310-I/PT Datasheet - Page 180

• Manufacturer Part Number: PIC18LF6310-I/PT
• Description: IC PIC MCU FLASH 4KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF6310-I/PT

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 54
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• No. Of Pwm: RoHS Compliant
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F6310/6410/8310/8410
16.4
The MSSP module in I
master and slave functions (including general call
support) and provides interrupts on Start and Stop bits
in hardware to determine a free bus (multi-master
function). The MSSP module implements the standard
mode specifications as well as 7-bit and 10-bit
addressing.
Two pins are used for data transfer:
• Serial clock (SCL) – RC3/SCK/SCL
• Serial data (SDA) – RC4/SDI/SDA
The user must configure these pins as inputs through
the TRISC<4:3> bits.
FIGURE 16-7:
DS39635B-page 178
RC3/SCK/SCL
RC4/
SDA
SDI/
I
2
C Mode
Read
Shift
Clock
MSb
MSSP BLOCK DIAGRAM
(I
Stop bit Detect
2
2
SSPADD reg
Match Detect
C mode fully implements all
C™ MODE)
SSPSR reg
SSPBUF reg
Start and
LSb
Write
(SSPSTAT reg)
Set, Reset
S, P bits
Internal
Data Bus
Addr Match
Preliminary
16.4.1
The MSSP module has six registers for I
These are:
• MSSP Control Register 1 (SSPCON1)
• MSSP Control Register 2 (SSPCON2)
• MSSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer Register
• MSSP Shift Register (SSPSR) – Not directly
• MSSP Address Register (SSPADD)
SSPCON1, SSPCON2 and SSPSTAT are the control
and status registers in I
SSPCON1 and SSPCON2 registers are readable and
writable. The lower 6 bits of the SSPSTAT are read-only.
The upper 2 bits of the SSPSTAT are read/write.
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to, or read from.
SSPADD register holds the slave device address
when the MSSP is configured in I
When the MSSP is configured in Master mode, the
lower 7 bits of SSPADD act as the Baud Rate
Generator reload value.
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
During transmission, the SSPBUF is not double-
buffered. A write to SSPBUF will write to both SSPBUF
and SSPSR.
(SSPBUF)
accessible
REGISTERS
© 2007 Microchip Technology Inc.
2
C mode operation. The
2
C Slave mode.
2
C operation.