PIC18F24J10-I/SP Microchip Technology, PIC18F24J10-I/SP Datasheet - Page 74

• Manufacturer Part Number: PIC18F24J10-I/SP
• Description: IC PIC MCU FLASH 8KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F24J10-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPIC/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162074 - HEADER INTRFC MPLAB ICD2 44TQFPAC162067 - HEADER INTRFC MPLAB ICD2 40/28P
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F45J10 FAMILY
FIGURE 7-2:
7.2
Several control registers are used in conjunction with
the TBLRD and TBLWT instructions. These include the:
• EECON1 register
• EECON2 register
• TABLAT register
• TBLPTR registers
7.2.1
The EECON1 register (Register 7-1) is the control
register for memory accesses. The EECON2 register is
not a physical register; it is used exclusively in the
memory
EECON2 will read all ‘0’s.
The FREE bit, when set, will allow a program memory
erase operation. When FREE is set, the erase
operation is initiated on the next WR command. When
FREE is clear, only writes are enabled.
DS39682E-page 72
Note 1: Table Pointer actually points to one of 64 holding registers, the address of which is determined by
Control Registers
write
TBLPTRU
EECON1 AND EECON2 REGISTERS
TBLPTRL<5:0>. The process for physically writing data to the program memory array is discussed in
Section 7.5 “Writing to Flash Program Memory”.
and
Table Pointer
TABLE WRITE OPERATION
TBLPTRH
erase
sequences.
(1)
TBLPTRL
Program Memory
(TBLPTR)
Reading
Instruction: TBLWT*
Holding Registers
Program Memory
The WREN bit, when set, will allow a write operation.
On power-up, the WREN bit is clear. The WRERR bit is
set in hardware when the WR bit is set and cleared
when the internal programming timer expires and the
write operation is complete.
The WR control bit initiates write operations. The bit
cannot be cleared, only set, in software; it is cleared in
hardware at the completion of the write operation.
Note:
During normal operation, the WRERR is
read as ‘1’. This can indicate that a write
operation was prematurely terminated by
a Reset, or a write operation was
attempted improperly.
© 2009 Microchip Technology Inc.
Table Latch (8-bit)
TABLAT