PIC18F24J10-I/SP Microchip Technology, PIC18F24J10-I/SP Datasheet - Page 195

• Manufacturer Part Number: PIC18F24J10-I/SP
• Description: IC PIC MCU FLASH 8KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F24J10-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPIC/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162074 - HEADER INTRFC MPLAB ICD2 44TQFPAC162067 - HEADER INTRFC MPLAB ICD2 40/28P
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

17.0
The Enhanced Universal Synchronous Asynchronous
Receiver Transmitter (EUSART) module is one of the
two serial I/O modules. (Generically, the USART is also
known as a Serial Communications Interface or SCI.)
The EUSART can be configured as a full-duplex,
asynchronous system that can communicate with
peripheral devices, such as CRT terminals and
personal computers. It can also be configured as a half-
duplex synchronous system that can communicate
with peripheral devices, such as A/D or D/A integrated
circuits, serial EEPROMs, etc.
The Enhanced USART module implements additional
features, including automatic baud rate detection and
calibration, automatic wake-up on Sync Break recep-
tion and 12-bit Break character transmit. These make it
ideally suited for use in Local Interconnect Network
(LIN/J2602) bus systems.
The EUSART can be configured in the following
modes:
• Asynchronous (full duplex) with:
• Synchronous – Master (half duplex) with
• Synchronous – Slave (half duplex) with selectable
© 2009 Microchip Technology Inc.
- Auto-wake-up on character reception
- Auto-baud calibration
- 12-bit Break character transmission
selectable clock polarity
clock polarity
ENHANCED UNIVERSAL
SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (EUSART)
PIC18F45J10 FAMILY
The pins of the Enhanced USART are multiplexed
with PORTC. In order to configure RC6/TX/CK and
RC7/RX/DT as an EUSART:
• bit SPEN (RCSTA<7>) must be set (= 1)
• bit TRISC<7> must be set (= 1)
• bit TRISC<6> must be set (= 1)
The operation of the Enhanced USART module is
controlled through three registers:
• Transmit Status and Control (TXSTA)
• Receive Status and Control (RCSTA)
• Baud Rate Control (BAUDCON)
These are detailed on the following pages in
Register 17-1,
respectively.
Note:
The EUSART control will automatically
reconfigure the pin from input to output as
needed.
Register 17-2
and
DS39682E-page 193
Register 17-3,