PIC16F506-I/SL Microchip Technology, PIC16F506-I/SL Datasheet - Page 53

• Manufacturer Part Number: PIC16F506-I/SL
• Description: IC PIC MCU FLASH 1KX14 14SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F506-I/SL

• Program Memory Type: FLASH
• Program Memory Size: 1.5KB (1K x 12)
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 11
• Ram Size: 67 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 67 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 3-ch x 8-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

9.0
The A/D Converter allows conversion of an analog
signal into an 8-bit digital signal.
9.1
The ADC has 4 clock source settings ADCS<1:0>.
There are 3 divisor values 16, 8 and 4. The fourth set-
ting is INTOSC with a divisor of 4. These settings will
allow a proper conversion when using an external
oscillator at speeds from 20 MHz to 350 kHz. Using
an external oscillator at a frequency below 350 kHz
(TAD > 50 μs) requires the ADC oscillator setting to be
INTOSC/4 for valid ADC results.
The ADC requires 13 T
conversion. The divisor values do not affect the number
of T
divisor values determine the length of the T
When the ADCS<1:0> bits are changed while an ADC
conversion is in process, the new ADC clock source will
not be selected until the next conversion is started. This
clock source selection will be lost when the device
enters Sleep.
9.1.1
There is no external voltage reference for the ADC. The
ADC reference voltage will always be V
9.1.2
The ANS<1:0> bits are used to configure pins for
analog input. Upon any Reset, ANS<1:0> defaults to
11. This configures pins AN0, AN1 and AN2 as analog
inputs. Pins configured as analog inputs are not avail-
able for digital output. Users should not change the
ANS bits while a conversion is in process. ANS bits are
active regardless of the condition of ADON.
9.1.3
The CHS bits are used to select the analog channel to
be sampled by the ADC. The CHS<1:0> bits can be
changed at any time without adversely effecting a con-
version. To acquire an analog signal the CHS<1:0>
selection must match one of the pin(s) selected by the
ANS<1:0> bits. When the ADC is on (ADON = 1) and a
channel is selected that is also being used by the
comparator, then both the comparator and the ADC will
see the analog voltage on the pin.
© 2007 Microchip Technology Inc.
Note:
AD
periods required to perform a conversion. The
ANALOG-TO-DIGITAL (A/D)
CONVERTER
Clock Divisors
VOLTAGE REFERENCE
ANALOG MODE SELECTION
ADC CHANNEL SELECTION
It is the users responsibility to ensure that
use of the ADC and comparator simulta-
neously on the same pin, does not
adversely
monitored or adversely effect device
operation.
affect
AD
periods to complete a
the
signal
DD
.
AD
period.
being
When the CHS<1:0> bits are changed during an ADC
conversion, the new channel will not be selected until
the current conversion is completed. This allows the
current conversion to complete with valid results. All
channel selection information will be lost when the
device enters Sleep.
TABLE 9-1:
9.1.4
The GO/DONE bit is used to determine the status of a
conversion, to start a conversion and to manually halt a
conversion in process. Setting the GO/DONE bit starts
a conversion. When the conversion is complete, the
ADC module clears the GO/DONE bit. A conversion
can be terminated by manually clearing the GO/DONE
bit while a conversion is in process. Manual termination
of a conversion may result in a partially converted
result in ADRES.
The GO/DONE bit is cleared when the device enters
Sleep, stopping the current conversion. The ADC does
not have a dedicated oscillator, it runs off of the instruc-
tion clock. Therefore, no conversion can occur in sleep.
The GO/DONE bit cannot be set when ADON is clear.
MCLR
Conversion completed
Conversion terminated
Power-on
Wake from Sleep
PIC12F510/16F506
THE GO/DONE BIT
Event
CHANNEL SELECT (ADCS)
BITS AFTER AN EVENT
DS41268D-page 51
ADCS<1:0>
CS<1:0>
CS<1:0>
11
11
11