CY8C3446LTI-085ES2 Cypress Semiconductor Corp, CY8C3446LTI-085ES2 Datasheet - Page 25

• Manufacturer Part Number: CY8C3446LTI-085ES2
• Manufacturer: Cypress Semiconductor Corp

Specifications of CY8C3446LTI-085ES2

• Lead Free Status / Rohs Status: Supplier Unconfirmed

access to peripherals through the DSI. Full information on I/O
ports is found in
I/O ports are linked to the CPU through the PHUB and are also
available in the SFRs. Using the SFRs allows faster access to a
limited set of I/O port registers, while using the PHUB allows boot
configuration and access to all I/O port registers.
Each SFR supported I/O port provides three SFRs:
5.7.3.1 xdata Space
The 8051 xdata space is 24-bit, or 16 MB in size. The majority of
this space is not “external”—it is used by on-chip components.
See
accessed using the EMIF. See
page 23.
Table 5-5. XDATA Data Address Map
Document Number: 001-53304 Rev. *L
0×00 0000 – 0×00 1FFF SRAM
0×00 4000 – 0×00 42FF Clocking, PLLs, and oscillators
0×00 4300 – 0×00 43FF Power management
0×00 4400 – 0×00 44FF Interrupt controller
0×00 4500 – 0×00 45FF Ports interrupt control
0×00 4700 – 0×00 47FF Flash programming interface
0×00 4900 – 0×00 49FF I
0×00 4E00 – 0×00
4EFF
0×00 4F00 – 0×00
4FFF
0×00 5000 – 0×00 51FF I/O ports control
0×00 5400 – 0×00 54FF External Memory Interface (EMIF)
0×00 5800 – 0×00 5FFF Analog Subsystem interface
0×00 6000 – 0×00 60FF USB controller
0×00 6400 – 0×00 6FFF UDB configuration
0×00 7000 – 0×00 7FFF PHUB configuration
0×00 8000 – 0×00 8FFF EEPROM
0×00 A000 – 0×00
A400
SFRPRTxDR sets the output data state of the port (where x is
port number and includes ports 0-6, 12 and 15)
The SFRPRTxSEL selects whether the PHUB PRTxDR
register or the SFRPRTxDR controls each pin’s output buffer
within the port. If a SFRPRTxSEL[y] bit is high, the
corresponding SFRPRTxDR[y] bit sets the output state for that
pin. If a SFRPRTxSEL[y] bit is low, the corresponding
PRTxDR[y] bit sets the output state of the pin (where y varies
from 0 to 7).
The SFRPRTxPS is a read only register that contains pin state
values of the port pins.
Address Range
Table
5-5. External, that is, off-chip, memory can be
I/O System and Routing
Decimator
Fixed timer/counter/PWMs
control registers
CAN
2
C controller
External Memory Interface
Purpose
on page 32.
on
Table 5-5. XDATA Data Address Map (continued)
6. System Integration
6.1 Clocking System
The clocking system generates, divides, and distributes clocks
throughout the PSoC system. For the majority of systems, no
external crystal is required. The IMO and PLL together can
generate up to a 50 MHz clock, accurate to ±1 percent over
voltage and temperature. Additional internal and external clock
sources allow each design to optimize accuracy, power, and
cost. All of the system clock sources can be used to generate
other clock frequencies in the 16-bit clock dividers and UDBs for
anything the user wants, for example a UART baud rate
generator.
Clock generation and distribution is automatically configured
through the PSoC Creator IDE graphical interface. This is based
on the complete system’s requirements. It greatly speeds the
design process. PSoC Creator allows you to build clocking
systems with minimal input. You can specify desired clock
frequencies and accuracies, and the software locates or builds a
clock that meets the required specifications. This is possible
because of the programmability inherent PSoC.
Key features of the clocking system include:
0×01 0000 – 0×01
FFFF
0×05 0220 – 0×05 02F0 Debug controller
0×08 0000 – 0×08 1FFF Flash ECC bytes
0×80 0000 – 0×FF
FFFF
Seven general purpose clock sources
IMO has a USB mode that auto locks to the USB bus clock
requiring no external crystal for USB. (USB equipped parts only)
Independently sourced clock in all clock dividers
Eight 16-bit clock dividers for the digital system
Four 16-bit clock dividers for the analog system
Dedicated 16-bit divider for the bus clock
Dedicated 4-bit divider for the CPU clock
Automatic clock configuration in PSoC Creator
Address Range
3- to 24-MHz IMO, ±1 percent at 3 MHz
4- to 25-MHz external crystal oscillator (MHzECO)
Clock doubler provides a doubled clock frequency output for
the USB block, see
DSI signal from an external I/O pin or other logic
24- to 50- MHz fractional PLL sourced from IMO, MHzECO,
or DSI
1 kHz, 33 kHz, 100 kHz ILO for Watch Dog Timer (WDT) and
Sleep Timer
32.768-kHz external crystal oscillator (kHzECO) for RTC
PSoC
USB Clock Domain
Digital Interconnect configuration
External Memory Interface
®
3: CY8C34 Family
Purpose
on page 28
Data Sheet
Page 25 of 127