DSPIC33EP512MU810T-I/PT Microchip Technology, DSPIC33EP512MU810T-I/PT Datasheet - Page 166

• Manufacturer Part Number: DSPIC33EP512MU810T-I/PT
• Description: 100 PINS, 512KB Flash, 52KB RAM, 60 MHz, USB, 2xCAN, 15 DMA 100 TQFP 12x12x1mm T
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33EPr

Specifications of DSPIC33EP512MU810T-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 60 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, QEI, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 83
• Program Memory Size: 512KB (170K x 24)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 24K x 16
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

dsPIC33EPXXXMU806/810/814 and PIC24EPXXXGU810/814
REGISTER 9-1:
DS70616E-page 166
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14-12
bit 11
bit 10-8
bit 7
bit 6
bit 5
bit 4
Note 1:
CLKLOCK
R/W-0
U-0
—
2:
3:
Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70580) in the
“dsPIC33E/PIC24E Family Reference Manual” (available from the Microchip web site) for details.
Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
This applies to clock switches in either direction. In these instances, the application must switch to FRC
mode as a transition clock source between the two PLL modes.
This register resets only on a Power-on Reset (POR).
Unimplemented: Read as ‘0’
COSC<2:0>: Current Oscillator Selection bits (read-only)
111 = Fast RC Oscillator (FRC) with Divide-by-N
110 = Fast RC Oscillator (FRC) with Divide-by-16
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (S
011 = Primary Oscillator (XT, HS, EC) with PLL
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator (FRC) with Divide-by-N and PLL
000 = Fast RC Oscillator (FRC)
Unimplemented: Read as ‘0’
NOSC<2:0>: New Oscillator Selection bits
111 = Fast RC Oscillator (FRC) with Divide-by-N
110 = Fast RC Oscillator (FRC) with Divide-by-16
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (S
011 = Primary Oscillator (XT, HS, EC) with PLL
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator (FRC) with Divide-by-N and PLL
000 = Fast RC Oscillator (FRC)
CLKLOCK: Clock Lock Enable bit
1 = If (FCKSM0 = 1), then clock and PLL configurations are locked
0 = Clock and PLL selections are not locked, configurations may be modified
IOLOCK: I/O Lock Enable bit
1 = I/O Lock is active
0 = I/O Lock is not active
LOCK: PLL Lock Status bit (read-only)
1 = Indicates that PLL is in lock, or PLL start-up timer is satisfied
0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled
Unimplemented: Read as ‘0’
IOLOCK
R/W-0
If (FCKSM0 = 0), then clock and PLL configurations may be modified
R-0
OSCCON: OSCILLATOR CONTROL REGISTER
COSC<2:0>
y = Value set from Configuration bits on POR
W = Writable bit
‘1’ = Bit is set
LOCK
R-0
R-0
OSC
OSC
R-0
U-0
Preliminary
—
)
)
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/C-0
U-0
CF
—
R/W-y
(1,3)
U-0
—
 2009-2011 Microchip Technology Inc.
NOSC<2:0>
x = Bit is unknown
LPOSCEN
R/W-0
R/W-y
(2)
OSWEN
R/W-y
R/W-0
bit 8
bit 0