EVAL-AD1954EB Analog Devices Inc, EVAL-AD1954EB Datasheet - Page 19

• Manufacturer Part Number: EVAL-AD1954EB
• Description: BOARD EVAL FOR AD1954
• Manufacturer: Analog Devices Inc

Specifications of EVAL-AD1954EB

• Rohs Status: RoHS non-compliant

SPI PORT
Overview
The AD1954 has many different control options. Most signal
processing parameters are controlled by writing new values to
the parameter RAM using the SPI port. Other functions, such as
volume and de-emphasis filtering, are programmed by writing to
the SPI control registers.
The SPI port uses a 4-wire interface, consisting of CLATCH,
CCLK, CDATA, and COUT signals. The CLATCH signal goes
low at the beginning of a transaction and high at the end of a
transaction. The CCLK signal latches the serial input data on a
low-to-high transition. The CDATA signal carries the serial input
data, and the COUT signal is the serial output data. The COUT
signal remains three-stated until a read operation is requested.
This allows other SPI compatible peripherals to share the same
readback line.
The SPI port is capable of full read/write operation for all of the
memories (parameter and program) and some of the SPI registers
(Control Register 1 and the data capture registers).The memories
may be accessed in both a single address mode or in burst mode.
All SPI transactions follow the same basic format that is shown in
Table I.
Byte 0
00000, R/W
00000, R/W
00000, R/ , Addr[9:8] Addr[7:0] Data
REV. A
CLATCH
CDATA
CCLK
CLATCH
CDATA
Table I. SPI Word Format
COUT
CCLK
Byte 1
BYTE 0
Figure 16. Sample of SPI Write Format (Single-Write Mode)
Figure 17. Sample of SPI Read Format (Single-Write Mode)
Byte 2
HI-Z
BYTE 0
Byte 3
Data
BYTE 1
Byte 4
Data
–19–
DATA
The R/W
The R/W
The R/
The 10-bit address word is decoded into either a location in one
of the two memories (parameter or program) or one of the SPI
registers. The number of data bytes varies according to the regis-
ter or memory being accessed. In burst-write mode (available for
loading the RAMs only), an initial address is given followed by a
continuous sequence of data for consecutive RAM locations. The
detailed data format diagram for continuous-mode operation is
given in SPI read/write data formats.
A sample timing diagram for a single SPI write operation to the
parameter RAM is shown in Figure 16.
A sample timing diagram of a single SPI read operation is shown
in Figure 17. The COUT pin goes from three-state to driven at
the beginning of Byte 2. Bytes 0 and 1 contain the address and
R/W
R/W
R/
is shown in Tables VIII to XIX.
The AD1954 has several mechanisms for updating signal-processing
parameters in real time without causing loud pops or clicks. In
cases where large blocks of data need to be downloaded, the DSP
core can be shut down and new data loaded, and then the core
can be restarted.The shutdown and restart mechanisms employ a
gradual volume ramp to prevent clicks and pops. In cases where
only a few parameters need to be changed (e.g., a single biquad
filter), a safeload mechanism is used, which allows a block of SPI
registers to be transferred to the parameter RAM within a single
audio frame while the core is running. The safeload mode uses
internal logic to prevent contention between the DSP core and
the SPI port.
W bit, and Bytes 2 through 4 carry the data. The exact format
W
BYTE 1
bit, and Bytes 2 through 4 carry the data. The exact format
W bit is low for a write and high for a read operation.
W
bit is low for a write and high for a read operation.
DATA
XXX
DATA
BYTE 4
HI-Z
AD1954