STEVAL-PCC010V1 STMicroelectronics, STEVAL-PCC010V1 Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STEVAL-PCC010V1
Manufacturer Part Number
STEVAL-PCC010V1
Description
BOARD EVAL FOR ST802RT1
Manufacturer
STMicroelectronics
Datasheets
1.ST802RT1AFR.pdf
(58 pages)
2.STEVAL-PCC010V1.pdf
(37 pages)
3.STEVAL-PCC010V1.pdf
(9 pages)
Specifications of STEVAL-PCC010V1
Main Purpose
Interface, Ethernet Controller (PHY and MAC)
Embedded
Yes, MCU, 8-Bit
Utilized Ic / Part
ST802RT1
Primary Attributes
1 Port, 100BASE-TX/10BASE-T
Secondary Attributes
MII, RMII
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-10360
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STEVAL-PCC010V1
Manufacturer:
STMicroelectronics
Quantity:
3
Registers and descriptors description
Table 20.
28/58
15:11
Bit
10
9
8
7
6
5
4
3
2
1
0
Auto neg interrupt
Auto-Negotiation
Link Code Word
Auto neg page
Remote fault
RESERVED
FX_MODE
Link down
Link down
RX_FULL
Bit name
Received
interrupt
interrupt
interrupt
received
RN11 [0d17, 0x11]: Receiver configuration information and interrupt status register
Duplex
Speed
Pause
---
1 -> FX mode set
0 -> FX mode not set
If set to '1', auto-negotiation and scrambling is disabled. This
bit can be set through an opportune hardware topology in
ST802RT1B
1 -> 100 Mb/s mode
0 -> 10 Mb/s mode
This bit holds a valid value only if a link is already established
1 -> Full-duplex mode enabled
0 -> Half-duplex mode enabled
This bit holds a valid value only if a link is already established
1 -> Pause is enabled
0 -> Pause is disabled
Pause is active only after auto-negotiation completion, if both
devices; support symmetric pause (RN04[10], RN05[10])
1 -> “Auto-negotiation completed” interrupt is pending
0 -> Auto-negotiation not yet completed
Interrupt enabled by RN12[6]
1 -> “Remote fault condition” interrupt is pending
0 -> No remote fault condition detected
Interrupt enabled by RN12[5]
1 -> “link status changed to fail” interrupt is pending
0 -> no link status changes
Interrupt enabled by RN12[4]
1 -> “acknowledge match” interrupt is pending
0 -> no link code word received
Interrupt enabled by RN12[3]
1 -> “Parallel Detection fault” interrupt is pending
0 -> No Parallel Detection faults
Interrupt enabled by RN12[2]
1 -> “Auto-negotiation page received” interrupt is pending
0 -> no auto-negotiation page received
Interrupt enabled by RN12[1]
1 -> “receive error buffer full” interrupt is pending (64k packet
errors)
0 -> less than 64k error packets received
Interrupt enabled by RN12[0]. Related counter is cleared
after read
Doc ID 17049 Rev 1
Description
ST802RT1A, ST802RT1B
Default
00000b
0
0
0
0
0
0
0
0
0
0
0
type
RW
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
RO
Type
LH
LH
LH
LH
LH
LH
LH
P
-
-
-
-