KP-FSD3 Panduit Corp, KP-FSD3 Datasheet - Page 207

• Manufacturer Part Number: KP-FSD3
• Description: KIT FERRULE INS DIN AWG12-6
• Manufacturer: Panduit Corp
• Series: Pan-Term®r
• Type: Ferrule Kitr

Specifications of KP-FSD3

• Kit Type: Ferrule - Wire End
• Values: 100 pcs - Assorted Insulated 12 ~ 6 AWG Ferrules
• Kit Contents: 50 Pieces Of FSD81-10, 20 Pieces Each Of FSD82-12 And FSD83-12, 10 Pieces Of FSD84-12
• Mounting Method: Crimp
• Where Used: To terminate stranded wire for insertion into terminal blocks
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Proper Installation Techniques For Pressure Sensitive Adhesive Mounts
For proper installation of adhesive mounts with foam tape, simply remove the release liner and place the mount
in the desired location. Avoid touching the adhesive prior to positioning the mount. Apply firm pressure to the
mount for 5 seconds to insure proper adhesion.
1) Clean surface with a
Selection and Use of Adhesive Mounts (continued)
Surface Preparation
For best results, Panduit adhesive mounts should be applied to clean, dry, grease-free surfaces.
We recommend that the surface be cleaned prior to mount installation. For rubber and acrylic based
foam tape adhesives, a blend of isopropyl alcohol and water 50/50 may be used to clean most surfaces.
For epoxy type adhesives, especially masonry surfaces, be sure to clean all loose particles away before mount
installation. Some surface abrasion is recommended to achieve maximum strength. A light rubbing with medium
grit emery cloth or sandpaper is best. Wash after abrading.
Proper Storage Conditions
All Panduit adhesive products have an expiration date printed on the package label. Use the following
storage guidelines:
1. For rubber and acrylic based foam tape adhesives, store in temperatures of 70°F (21°C) and 45%
Relative Humidity (R.H.).
2. For epoxy type adhesives, store in temperatures of 40°F (4°C) to 75°F (25°C) and relative humidity not in
excess of 45%. Storage in opened containers is not recommended. Using the guidelines above, the shelf life of
foam tape is 3 years. Shelf life of epoxy is 1 year. Deviation from the recommended storage conditions may
reduce the shelf life or adhesive strength. In any case, adhesive products should never be stored near heating
vents or other heat sources, and storage in lower temperatures than those recommended may increase the
shelf life.
Stock Rotation
Adhesive mount inventory should be rotated in order to
insure the quality of the adhesive foam tape. Each package
of Panduit adhesive backed mounts has a quality control
number and a best-if-used-by date on the package label.
The best-if-used-by date provides the customer with an
accurate way to control the rotation of inventory, and,
as is the case with all Panduit products, the quality control
number provides complete traceability for all components
that go into a specific production run of product.
Mount Removal
There is no simple or easy method for removing Panduit adhesives. A thin wire or razor blade can be moved
in between the surfaces when removing foam tape mounts; however, the adhesive residue will remain on the
surface. Epoxy adhesives may be removed with a commercial paint stripping solution.
clean cloth and
isopropyl alcohol.
Alcohol
2) Allow surface to air dry.
For technical assistance in the U.S., call 866-405-6654 (outside the U.S., see inside back cover for directory)
3) Remove the release
ELECTRICAL SOLUTIONS
liner, being careful not
to touch the adhesive.
4) Apply full thumb
Best-If-Used-By Date
pressure for at least
5 seconds.
Quality Control Number
5) Allow mount to
properly dwell.
9
12
6
3
B2.55
Management
Identification
Accessories
Connectors
Connectors
Grounding
Pre-Printed
& Write-On
Protection
Permanent
Solutions
Cable Ties
Terminals
Lockout/
Overview
Steel Ties
& Safety
Stainless
Raceway
Abrasion
Labeling
Systems
Surface
Markers
Tagout
System
Wiring
Labels
Power
Cable
Cable
Index
Duct
E5.
B1.
B2.
B3.
D1.
D2.
D3.
C1.
C2.
C3.
C4.
E1.
E2.
E3.
E4.
A.
F.