S9S08DZ60F2MLH Freescale Semiconductor, S9S08DZ60F2MLH Datasheet - Page 295

• Manufacturer Part Number: S9S08DZ60F2MLH
• Description: 8-bit Microcontrollers - MCU M74K MASK ONLY-AUTO
• Manufacturer: Freescale Semiconductor

Specifications of S9S08DZ60F2MLH

• Rohs: yes
• Core: HCS08
• Processor Series: MC9S08DZ60
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Program Memory Size: 60 KB
• Data Ram Size: 4 K
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-64
• Mounting Style: SMD/SMT

14.2.2
This read/write register is used to control various optional features of the SCI system.
Freescale Semiconductor
SCISWAI
SBR[7:0]
Reset
Reset
LOOPS
RSRC
Field
Field
7:0
M
7
6
5
4
W
W
R
R
LOOPS
SBR7
SCI Control Register 1 (SCIxC1)
Baud Rate Modulo Divisor — These 13 bits in SBR[12:0] are referred to collectively as BR, and they set the
modulo divide rate for the SCI baud rate generator. When BR = 0, the SCI baud rate generator is disabled to
reduce supply current. When BR = 1 to 8191, the SCI baud rate = BUSCLK/(16×BR). See also BR bits in
Table
Loop Mode Select — Selects between loop back modes and normal 2-pin full-duplex modes. When
LOOPS = 1, the transmitter output is internally connected to the receiver input.
0 Normal operation — RxD and TxD use separate pins.
1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input. (See
SCI Stops in Wait Mode
0 SCI clocks continue to run in wait mode so the SCI can be the source of an interrupt that wakes up the CPU.
1 SCI clocks freeze while CPU is in wait mode.
Receiver Source Select — This bit has no meaning or effect unless the LOOPS bit is set to 1. When
LOOPS = 1, the receiver input is internally connected to the TxD pin and RSRC determines whether this
connection is also connected to the transmitter output.
0 Provided LOOPS = 1, RSRC = 0 selects internal loop back mode and the SCI does not use the RxD pins.
1 Single-wire SCI mode where the TxD pin is connected to the transmitter output and receiver input.
9-Bit or 8-Bit Mode Select
0 Normal — start + 8 data bits (LSB first) + stop.
1 Receiver and transmitter use 9-bit data characters
0
0
7
7
RSRC
start + 8 data bits (LSB first) + 9th data bit + stop.
14-2.
bit.) RxD pin is not used by SCI.
SCISWAI
SBR6
0
0
6
6
Figure 14-5. SCI Baud Rate Register (SCIxBDL)
Figure 14-6. SCI Control Register 1 (SCIxC1)
Table 14-3. SCIxBDL Field Descriptions
Table 14-4. SCIxC1 Field Descriptions
MC9S08DZ60 Series Data Sheet, Rev. 4
RSRC
SBR5
0
0
5
5
SBR4
M
0
0
4
4
Description
Description
WAKE
SBR3
Chapter 14 Serial Communications Interface (S08SCIV4)
3
0
3
0
SBR2
ILT
1
0
2
2
SBR1
PE
0
0
1
1
SBR0
PT
0
0
0
0
295