S9S08SG8E2VTG Freescale Semiconductor, S9S08SG8E2VTG Datasheet - Page 294

• Manufacturer Part Number: S9S08SG8E2VTG
• Description: 8-bit Microcontrollers - MCU 9S08 UC W/ 8K 0.25UM SGF
• Manufacturer: Freescale Semiconductor

Specifications of S9S08SG8E2VTG

• Rohs: yes
• Core: S08
• Processor Series: MC9S08SG8
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Program Memory Size: 8 KB
• Data Ram Size: 8 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 5.5 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: TSSOP-16
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Interface Type: SCI, SPI
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 2.7 V

1
2
3
4
5
6
7
8
9
10
11
Num C
23
24
Typical values are measured at 25C. Characterized, not tested.
Electrical characteristics only apply to the temperature rated devices marked with x.
When a pin interrupt is configured to detect rising edges, pulldown resistors are used in place of pullup resistors.
The specified resistor value is the actual value internal to the device. The pullup value may measure higher when measured externally on
the pin.
Power supply must maintain regulation within operating V
positive injection current (V
going out of regulation. Ensure external V
when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low (which would reduce overall
power consumption).
All functional non-supply pins are internally clamped to V
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance
values for positive and negative clamp voltages, then use the larger of the two values.
The RESET pin does not have a clamp diode to V
Maximum is highest voltage that POR will occur.
Simulated, not tested
Factory trimmed at V
Appendix A Electrical Characteristics
290
P Bandgap Voltage Reference
T
1.5
0.5
Low-voltage inhibit reset/recover
hysteresis
2
1
0
0
150°C
–40°C
25°C
Characteristic
DD
5
a) V
= 5.0 V
DD
In
> V
= 5V, High Drive
10
DD
I
OL
Max 1.5V@20mA
) is greater than I
11
(mA)
Figure A-1. Typical V
DD
15
Table A-6. DC Characteristics (continued)
MC9S08SG8 MCU Series Data Sheet, Rev. 7
load will shunt current greater than maximum injection current. This will be the greatest risk
Symbol
V
V
DD
hys
BG
20
DD
. Do not drive this pin above V
, the injection current may flow out of V
SS
DD
and V
range during instantaneous and operating maximum current conditions. If
OL
25
Condition
DD
vs I
5 V
3 V
.
OL
, High Drive Strength
1.0
0.8
0.6
0.4
0.2
0
0
150°C
–40°C
DD
25°C
1.18
1.17
Min
.
—
—
2
b) V
DD
DD
Typ
1.20
1.20
100
60
= 3V, High Drive
and could result in external power supply
4
1
I
OL
(mA)
Freescale Semiconductor
Max
1.21
1.22
Max 0.8V@5mA
—
—
6
Unit
mV
V
V
8
Stand
Temp Rated
ard
x
x
x
10
Grade
AEC
0
x
x
x
2