MC9S08AW60 FREESCALE [Freescale Semiconductor, Inc], MC9S08AW60 Datasheet - Page 298
![no-image](/images/no-image-200.jpg)
MC9S08AW60
Manufacturer Part Number
MC9S08AW60
Description
Microcontrollers
Manufacturer
FREESCALE [Freescale Semiconductor, Inc]
Datasheet
1.MC9S08AW60.pdf
(324 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC9S08AW60
Manufacturer:
FREESCAL
Quantity:
670
Company:
Part Number:
MC9S08AW60CFDE
Manufacturer:
FREESCALE
Quantity:
1 001
Company:
Part Number:
MC9S08AW60CFGE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MC9S08AW60CFGER
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC9S08AW60CFUE
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
MC9S08AW60CPUE
Manufacturer:
TDK-LAMBDA
Quantity:
92
Company:
Part Number:
MC9S08AW60CPUE
Manufacturer:
FREESCALE
Quantity:
4 000
Part Number:
MC9S08AW60CPUE
Manufacturer:
FREESCALE
Quantity:
20 000
1
2
3
4
5
6
7
8
9
Appendix A Electrical Characteristics and Timing Specifications
298
Num
Typical values are based on characterization data at V
Self-clocked mode frequency is the frequency that the DCO generates when the FLL is open-loop.
Loss of reference frequency is the reference frequency detected internally, which transitions the ICG into self-clocked mode if it
is not in the desired range.
Loss of DCO frequency is the DCO frequency detected internally, which transitions the ICG into FLL bypassed external mode
(if an external reference exists) if it is not in the desired range.
This parameter is characterized before qualification rather than 100% tested.
Proper PC board layout procedures must be followed to achieve specifications.
This specification applies to the period of time required for the FLL to lock after entering FLL engaged internal or external modes.
If a crystal/resonator is being used as the reference, this specification assumes it is already running.
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via V
a given interval.
See
19
Figure
MC9S08AWxx: Internal oscillator deviation from trimmed frequency
S9S08AWxx: Internal oscillator deviation from trimmed frequency
C
C
C
P
P
P
A-9.
(V
V
V
V
V
V
DDA
DD
DD
DD
DD
DD
= 2.7 – 5.5 V, (constant temperature)
= 5.0 V ±10%, –40° C to 125°C
= 2.7 – 5.5 V, (constant temperature)
= 5.0 V ±10%, –40° C to 85°C
= 5.0 V ±10%, –40° C to 125°C
= V
DDA
Table A-12. ICG Frequency Specifications (continued)
(min) to V
Characteristic
DDA
and V
DDA
SSA
MC9S08AW60 Data Sheet, Rev 2
(max), Temperature Range = –40 to 125°C Ambient)
and variation in crystal oscillator frequency increase the C
DD
= 5.0V, 25°C unless otherwise stated.
Symbol
ACC
ACC
9
9
int
int
Min
—
—
—
—
—
Typ
±0.5
±0.5
±0.5
±0.5
±0.5
Freescale Semiconductor
1
Jitter
Max
±1.5
±1.5
±2
±2
±2
percentage for
ICGOUT
Unit
.
%
%
%
%
%