MC9S08AW60 FREESCALE [Freescale Semiconductor, Inc], MC9S08AW60 Datasheet - Page 188

no-image

MC9S08AW60

Manufacturer Part Number
MC9S08AW60
Description
Microcontrollers
Manufacturer
FREESCALE [Freescale Semiconductor, Inc]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC9S08AW60
Manufacturer:
FREESCAL
Quantity:
670
Part Number:
MC9S08AW60CFDE
Manufacturer:
FREESCALE
Quantity:
1 001
Part Number:
MC9S08AW60CFGE
Manufacturer:
FREESCALE
Quantity:
10 000
Part Number:
MC9S08AW60CFGE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC9S08AW60CFGE
Manufacturer:
FREESCALE
Quantity:
10 000
Part Number:
MC9S08AW60CFGER
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC9S08AW60CFUE
Manufacturer:
FREESCALE
Quantity:
50 000
Part Number:
MC9S08AW60CFUE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC9S08AW60CFUE
0
Part Number:
MC9S08AW60CPUE
Manufacturer:
TDK-LAMBDA
Quantity:
92
Part Number:
MC9S08AW60CPUE
Manufacturer:
FREESCALE
Quantity:
4 000
Part Number:
MC9S08AW60CPUE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC9S08AW60CPUE
Quantity:
7
Part Number:
MC9S08AW60CPUE
Quantity:
7
Part Number:
MC9S08AW60CPUE
0
Chapter 11 Serial Communications Interface (S08SCIV2)
11.2.3
This register can be read or written at any time.
188
Reset
Field
TCIE
ILIE
TIE
RIE
RE
TE
7
6
5
4
3
2
W
R
SCI Control Register 2 (SCIxC2)
TIE
Transmit Interrupt Enable (for TDRE)
0 Hardware interrupts from TDRE disabled (use polling).
1 Hardware interrupt requested when TDRE flag is 1.
Transmission Complete Interrupt Enable (for TC)
0 Hardware interrupts from TC disabled (use polling).
1 Hardware interrupt requested when TC flag is 1.
Receiver Interrupt Enable (for RDRF)
0 Hardware interrupts from RDRF disabled (use polling).
1 Hardware interrupt requested when RDRF flag is 1.
Idle Line Interrupt Enable (for IDLE)
0 Hardware interrupts from IDLE disabled (use polling).
1 Hardware interrupt requested when IDLE flag is 1.
Transmitter Enable
0 Transmitter off.
1 Transmitter on.
TE must be 1 in order to use the SCI transmitter. Normally, when TE = 1, the SCI forces the TxD pin to act as an
output for the SCI system. If LOOPS = 1 and RSRC = 0, the TxD pin reverts to being a port B general-purpose
I/O pin even if TE = 1.
When the SCI is configured for single-wire operation (LOOPS = RSRC = 1), TXDIR controls the direction of
traffic on the single SCI communication line (TxD pin).
TE also can be used to queue an idle character by writing TE = 0 then TE = 1 while a transmission is in progress.
Refer to
When TE is written to 0, the transmitter keeps control of the port TxD pin until any data, queued idle, or queued
break character finishes transmitting before allowing the pin to revert to a general-purpose I/O pin.
Receiver Enable — When the SCI receiver is off, the RxD pin reverts to being a general-purpose port I/O pin.
0 Receiver off.
1 Receiver on.
0
7
Section 11.3.2.1, “Send Break and Queued
TCIE
0
6
Table 11-4. SCIxC2 Register Field Descriptions
Figure 11-7. SCI Control Register 2 (SCIxC2)
RIE
0
5
MC9S08AW60 Data Sheet, Rev 2
ILIE
0
4
Description
Idle” for more details.
TE
3
0
RE
0
2
Freescale Semiconductor
RWU
0
1
SBK
0
0

Related parts for MC9S08AW60