PSD4235G2-12UIT STMICROELECTRONICS [STMicroelectronics], PSD4235G2-12UIT Datasheet - Page 44
PSD4235G2-12UIT
Manufacturer Part Number
PSD4235G2-12UIT
Description
Flash in-system programmable (ISP) peripherals for 16-bit MCUs (3.3 V supply)
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.PSD4235G2-12UIT.pdf
(124 pages)
- Current page: 44 of 124
- Download datasheet (918Kb)
Erasing Flash memory
9.2
9.3
44/124
Suspend Sector Erase
When a Sector Erase cycle is in progress, the Suspend Sector Erase instruction can be
used to suspend the cycle by writing 0B0h to any even address when an appropriate Sector
Select (FS0-FS7 or CSBOOT0-CSBOOT3) is high. (See
data from another Flash memory sector after the Erase cycle has been suspended.
Suspend Sector Erase is accepted only during the Flash Sector Erase instruction execution
and defaults to READ mode. A Suspend Sector Erase instruction executed during an Erase
timeout period, in addition to suspending the Erase cycle, terminates the time out period.
The Toggle Flag bit (DQ6/DQ14) stops toggling when the PSD internal logic is suspended.
The status of this bit must be monitored at an address within the Flash memory sector being
erased. The Toggle Flag bit (DQ6/DQ14) stops toggling between 0.1µs and 15 µs after the
Suspend Sector Erase instruction has been executed. The PSD is then automatically set to
READ mode.
If an Suspend Sector Erase instruction was executed, the following rules apply:
●
●
●
●
Resume Sector Erase
If a Suspend Sector Erase instruction was previously executed, the Erase cycle may be
resumed with this instruction. The Resume Sector Erase instruction consists of writing 030h
to any even address while an appropriate Sector Select (FS0-FS7 or CSBOOT0-CSBOOT3)
is high. (See
Attempting to read from a Flash memory sector that was being erased outputs invalid
data.
Reading from a Flash memory sector that was not being erased is valid.
The Flash memory cannot be programmed, and only responds to Resume Sector
Erase and Reset instructions (READ is an operation and is allowed).
If a Reset instruction is received, data in the Flash memory sector that was being
erased is invalid.
Table
28.)
Table
28). This allows reading of
PSD4235G2V
Related parts for PSD4235G2-12UIT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC FLASH 4MBIT 70NS 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 4MBIT 90NS 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 4MBIT 90NS 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Flash In-system Programmable Isp Peripherals For 16-bit Mcus 5v Supply
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: