PIC18F23K20-E/MLQTP MICROCHIP [Microchip Technology], PIC18F23K20-E/MLQTP Datasheet - Page 3

• Manufacturer Part Number: PIC18F23K20-E/MLQTP
• Description: 28/40/44-Pin Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
• Manufacturer: MICROCHIP [Microchip Technology]

Power-Managed Modes:
• Run: CPU on, peripherals on
• Idle: CPU off, peripherals on
• Sleep: CPU off, peripherals off
• Idle mode currents down to 1.0 μA, typical
• Sleep mode current down to 0.1 μA, typical
• Timer1 Oscillator: 1.0 μA, 32 kHz, 1.8V, typical
• Watchdog Timer: 2.0 μA, 1.8V, typical
• Two-Speed Oscillator Start-up
Peripheral Highlights:
• High-current sink/source 25 mA/25 mA
• Three programmable external interrupts
• Four independent input-change interrupts
• 8 independent weak pull-ups
• Programmable slew rate
• Capture/Compare/PWM (CCP) module
• Enhanced Capture/Compare/PWM (ECCP)
• Master Synchronous Serial Port (MSSP) module
• Enhanced Addressable USART module:
• 10-bit, up to 14-channel Analog-to-Digital
• Dual analog comparators
• Programmable On-Chip Voltage Reference
© 2007 Microchip Technology Inc.
module:
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-Shutdown and Auto-Restart
supporting 3-wire SPI (all 4 modes) and I
Master and Slave modes with address mask
- Supports RS-485, RS-232 and LIN 2.0
- RS-232 operation using internal oscillator
- Auto-Wake-up on Break
- Auto-Baud Detect
Converter module (ADC):
- Auto-acquisition capability
- Conversion available during Sleep
- Internal 1.2V Fixed Voltage Reference (FVR)
- Independent input multiplexing
- Rail-to-rail operation
- Independent input multiplexing
(CV
block (no external crystal required)
channel
REF
) module (% of V
28/40/44-Pin Flash Microcontrollers with
10-Bit A/D and nanoWatt Technology
DD
)
2
Advance Information
C™
PIC18F2XK20/4XK20
Flexible Oscillator Structure:
• Four Crystal modes, up to 64 MHz
• 4X Phase Lock Loop (available for crystal and
• Two External RC modes, up to 4 MHz
• Two External Clock modes, up to 64 MHz
• Internal oscillator block:
• Secondary oscillator using Timer1 @ 32 kHz
• Fail-Safe Clock Monitor:
Special Microcontroller Features:
• C compiler optimized architecture:
• Self-programmable under software control
• Priority levels for interrupts
• 8 x 8 Single-Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
• Single-supply 3V In-Circuit Serial
• In-Circuit Debug (ICD) via two pins
• Operating voltage range: 1.8V to 3.6V
• Programmable 16-level High/Low-Voltage
• Programmable Brown-out Reset (BOR)
internal oscillators)
- 8 user selectable frequencies, from 31 kHz to
- Provides a complete range of clock speeds
- User tunable to compensate for frequency drift
- Allows for safe shutdown if primary or secondary
- Optional extended instruction set designed to
- Programmable period from 4 ms to 131s
Programming™ (ICSP™) via two pins
Detection (HLVD) module:
- Supports interrupt on High/Low-Voltage
- With software enable option
16 MHz
from 31 kHz to 64 MHz when used with PLL
oscillator stops
optimize re-entrant code
Detection
DS41303B-page 1