pic24hj12gp202 Microchip Technology Inc., pic24hj12gp202 Datasheet - Page 89

• Manufacturer Part Number: pic24hj12gp202
• Description: High-performance, 16-bit Digital Signal Controllers
• Manufacturer: Microchip Technology Inc.

8.0
The PIC24HJ12GP201/202 devices provide the ability
to
managing clocking to the CPU and the peripherals. In
general, a lower clock frequency and a reduction in the
number of circuits being clocked constitutes lower
consumed power. PIC24HJ12GP201/202 devices can
manage power consumption in four different ways:
• Clock frequency
• Instruction-based Sleep and Idle modes
• Software-controlled Doze mode
• Selective peripheral control in software
Combinations of these methods can be used to
selectively tailor an application’s power consumption
while still maintaining critical application features, such
as timing-sensitive communications.
8.1
PIC24HJ12GP201/202 devices allow a wide range of
clock frequencies to be selected under application
control. If the system clock configuration is not locked,
users can choose low-power or high-precision
oscillators by simply changing the NOSC bits
(OSCCON<10:8>). The process of changing a system
clock during operation, as well as limitations to the
process, are discussed in more detail in Section 7.0
“Oscillator Configuration”.
EXAMPLE 8-1:
© 2007 Microchip Technology Inc.
PWRSAV #SLEEP_MODE
PWRSAV #IDLE_MODE
Note:
manage
POWER-SAVING FEATURES
Clock Frequency and Clock
Switching
This data sheet summarizes the features
of the PIC24HJ12GP201/202 devices. It is
not intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to the
“PIC24H
Please see the Microchip web site
(www.microchip.com)
PIC24H
chapters.
power
PWRSAV INSTRUCTION SYNTAX
Family
Family
consumption
; Put the device into SLEEP mode
; Put the device into IDLE mode
Reference
Reference
for
by
the
selectively
Manual”.
Manual
latest
Preliminary
PIC24HJ12GP201/202
8.2
PIC24HJ12GP201/202 devices have two special
power-saving modes that are entered through the
execution of a special PWRSAV instruction. Sleep mode
stops clock operation and halts all code execution. Idle
mode halts the CPU and code execution, but allows
peripheral modules to continue operation. The
Assembler syntax of the PWRSAV instruction is shown
in Example 8-1.
Sleep and Idle modes can be exited as a result of an
enabled interrupt, WDT time-out or a device Reset. When
the device exits these modes, it is said to wake-up.
8.2.1
The following occur in Sleep mode:
• The system clock source is shut down. If an on-
• The device current consumption is reduced to a
• The Fail-Safe Clock Monitor does not operate,
• The LPRC clock continues to run if the WDT is
• The WDT, if enabled, is automatically cleared
• Some device features or peripherals may continue
• Any peripheral that requires the system clock
The device will wake-up from Sleep mode on any of the
these events:
• Any interrupt source that is individually enabled
• Any form of device Reset
• A WDT time-out
On wake-up from Sleep mode, the processor restarts
with the same clock source that was active when Sleep
mode was entered.
chip oscillator is used, it is turned off.
minimum, provided that no I/O pin is sourcing
current.
since the system clock source is disabled.
enabled.
prior to entering Sleep mode.
to operate. This includes items such as the input
change notification on the I/O ports, or peripherals
that use an external clock input.
source for its operation is disabled.
Note:
Instruction-Based Power-Saving
Modes
SLEEP MODE
SLEEP_MODE and IDLE_MODE are con-
stants defined in the assembler include
file for the selected device.
DS70282B-page 87