psd813f1a-90ut STMicroelectronics, psd813f1a-90ut Datasheet - Page 49
psd813f1a-90ut
Manufacturer Part Number
psd813f1a-90ut
Description
Flash In-system Programmable Isp Peripherals For 8-bit Mcus
Manufacturer
STMicroelectronics
Datasheet
1.PSD813F1A-90UT.pdf
(94 pages)
- Current page: 49 of 94
- Download datasheet (539Kb)
The
PSD913F1
Functional
Blocks
(cont.)
48
PSD913F1
9.4.2.3 Address Out Mode
For microcontrollers with a multiplexed address/data bus, Address Out Mode can be used
to drive latched addresses onto the port pins. These port pins can, in turn, drive external
devices. Either the output enable or the corresponding bits of both the Direction Register
and Control Register must be set to a ‘1’ for pins to use Address Out Mode. This must be
done by the MCU at run-time. See Table 19 for the address output pin assignments on
Ports A and B for various MCUs.
For non-multiplexed 8 bit bus mode, address lines A[7:0] are available to Port B in Address
Out Mode.
Note: Do not drive address lines with Address Out Mode to an external memory device if it
is intended for the MCU to boot from the external device. The MCU must first boot from
PSD memory so the Direction and Control register bits can be set.
Table 19. I/O Port Latched Address Output Assignments
9.4.2.4 Address In Mode
For microcontrollers that have more than 16 address lines, the higher addresses can be
connected to Port A, B, C, and D. The address input can be latched by the address strobe
(ALE/AS). Any input that is included in the DPLD equations for the Main Flash, Secondary
Flash, or SRAM is considered to be an address input.
9.4.2.5 Data Port Mode
Port A can be used as a data bus port for a microcontroller with a non-multiplexed
address/data bus. The Data Port is connected to the data bus of the microcontroller. The
general I/O functions are disabled in Port A if the port is configured as a Data Port.
9.4.2.6 JTAG ISP
Port C is JTAG compliant, and can be used for In-System Programming (ISP). For more
information on the JTAG Port, refer to section 9.6.
N/A = Not Applicable.
8051XA (8-Bit)
80C251
(Page Mode)
All Other
8-Bit Multiplexed
8-Bit
Non-Multiplexed Bus
Microcontroller
N/A*
N/A
Address (3:0)
N/A
Port A (3:0)
Address (7:4)
N/A
Address (7:4)
N/A
Port A (7:4)
Address (11:8)
Address (11:8)
Address (3:0)
Address [3:0]
Port B (3:0)
N/A
Address (15:12)
Address (7:4)
Address [7:4]
Port B (7:4)
Preliminary
Related parts for psd813f1a-90ut
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Flash In-system Programmable Isp Peripherals For 8-bit Mcus, 5 V
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
IC FLASH 1MBIT 90NS 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 1MBIT 90NS 52QFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 1MBIT 120NS 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 1MBIT 90NS 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 1MBIT 90NS 52QFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 1MBIT 120NS 52PLCC
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 1MBIT 90NS 52PLCC
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH 1MBIT 90NS 52PLCC
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Flash In-System Programmable ISP Peripherals For 8-bit MCUs
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet: