st7fmc2s7t6 STMicroelectronics, st7fmc2s7t6 Datasheet - Page 247

• Manufacturer Part Number: st7fmc2s7t6
• Description: 8-bit Mcu With Nested Interrupts, Flash, 10-bit Adc, Brushless Motor Control, Five Timers, Spi, Linsci
• Manufacturer: STMicroelectronics

12.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
12.2.1 Voltage Characteristics
12.2.2 Current Characteristics
Notes:
1. Directly connecting the RESET and I/O pins to V
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).
To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7k
RESET, 10k
2. I
respected, the injection current must be limited externally to the I
while a negative injection is induced by V
3. All power (V
4. Negative injection disturbs the analog performance of the device. See note in
page
For best reliability, it is recommended to avoid negative injection of more than 1.6mA
5. When several inputs are submitted to a current injection, the maximum I
and negative injected currents (instantaneous values). These results are based on characterisation with I
mum current injection on four I/O port pins of the device.
| V
INJ(PIN)
I
283.
DDx
|V
INJ(PIN)
V
V
V
V
SSA
Symbol
Symbol
I
ESD(HBM)
DD
INJ(PIN)
PP
ESD(MM)
| and | V
I
I
V
VDD
VSS
must never be exceeded. This is implicitly insured if V
I
IO
- V
- V
- V
IN
2) & 4)
DD
for I/Os). For the same reason, unused I/O pins must not be directly tied to V
SS
SS
SSx
2)
) and ground (V
|
SSx
|
Supply voltage
Programming Voltage
Input voltage on any pin
Variations between different digital power pins
Variations between digital and analog ground pins
Electro-static discharge voltage (Human Body Model)
Electro-static discharge voltage (Machine Model)
Total current into V
(source)
Total current out of V
(sink)
Output current sunk by any standard I/O and control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control pin
Injected current on V
Injected current on RESET pin
Injected current on OSC1 and OSC2 pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
3)
SS
3)
) lines must always be connected to the external supply.
Ratings
IN
<V
DD
SS
PP
SS
power lines
.
Ratings
pin
ground lines
1) & 2)
DD
or V
5)
SS
could damage the device if an unintentional internal reset
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
INJ(PIN)
32-pin devices
44-pin devices
56, 64, 80-pin
devices
32-pin devices
44-pin devices
56, 64, 80-pin
devices
IN
maximum is respected. If V
value. A positive injection is induced by V
INJ(PIN)
5)
see
“ADC Accuracy with VDD=5.0V” on
is the absolute sum of the positive
V
Maximum value
Maximum value
SS
section 12.7.3 on page 262
-0.3 to V
DD
± 20
- 25
125
175
125
175
± 5
± 5
± 5
± 5
6.5
13
50
50
75
75
25
50
or V
ST7MC1/ST7MC2
IN
DD
maximum cannot be
SS
+0.3
.
INJ(PIN)
Unit
Unit
247/308
mV
mA
IN
V
maxi-
>V
for
DD