IDT70V27 Integrated Device Technology, IDT70V27 Datasheet - Page 18

• Manufacturer Part Number: IDT70V27
• Description: 32k X 16 3.3v Dual-port Ram
• Manufacturer: Integrated Device Technology

the other side is completed. If a write operation has been attempted from
the side that receives a BUSY indication, the write signal is gated internally
to prevent the write from proceeding.
In some cases it may be useful to logically OR the BUSY outputs together
and use any BUSY indication as an interrupt source to flag the event of
an illegal or illogical operation. If the write inhibit function of BUSY logic is
not desirable, the BUSY logic can be disabled by placing the part in slave
mode with the M/S pin. Once in slave mode the BUSY pin operates solely
as a write inhibit input pin. Normal operation can be programmed by tying
the BUSY pins HIGH. If desired, unintended write operations can be
prevented to a port by tying the BUSY pin for that port LOW.
pull type outputs and do not require pull up resistors to operate. If these
RAMs are being expanded in depth, then the BUSY indication for the
resulting array requires the use of an external AND gate.
Width Expansion with BUSY Logic
Master/Slave Arrays
A
logic, one master part is used to decide which side of the RAM array
will receive a BUSY indication, and to output that indication. Any number
of slaves to be addressed in the same address range as the master, use
the busy signal as a write inhibit signal. Thus on the IDT70V27 RAM the
BUSY pin is an output if the part is used as a master (M/S pin = V
the BUSY pin is an input if the part is used as a slave (M/S pin = V
shown in Figure 3.
decision could result with one master indicating BUSY on one side of the
array and another master indicating BUSY on one other side of the array.
This would inhibit the write operations from one port for part of a word and
inhibit the write operations from the other port for the other part of the word.
address signals only. It ignores whether an access is a read or write. In
a master/slave array, both address and chip enable must be valid long
enough for a BUSY flag to be output from the master before the actual write
pulse can be initiated with either the R/W signal or the byte enables. Failure
to observe this timing can result in a glitched internal write inhibit signal and
corrupted data in the slave.
15
BUSY
IDT 70V27S/L
High-Speed 3.3V 32K x 16 Dual-Port Static RAM
Figure 3. Busy and chip enable routing for both width and depth
The use of BUSY logic is not required or desirable for all applications.
The BUSY outputs on the IDT 70V27 RAM in master mode, are push-
When expanding an IDT70V27 RAM array in width while using BUSY
If two or more master parts were used when expanding in width, a split
The BUSY arbitration, on a master, is based on the chip enable and
L
MASTER
Dual Port RAM
MASTER
Dual Port RAM
BUSY
BUSY
L
L
expansion with IDT70V27 RAMs.
BUSY
BUSY
CE
CE
R
0
R
1
SLAVE
Dual Port RAM
SLAVE
Dual Port RAM
BUSY
BUSY
L
L
BUSY
BUSY
CE
CE
R
0
1
R
BUSY
3603 drw 17
IH
), and
IL
R
) as
18
,
Semaphores
an additional 8 address locations dedicated to binary semaphore flags.
These flags allow either processor on the left or right side of the Dual-Port
RAM to claim a privilege over the other processor for functions defined by
the system designer’s software. As an example, the semaphore can be
used by one processor to inhibit the other from accessing a portion of the
Dual-Port RAM or any other shared resource.
completely independent of each other. This means that the activity on the
left port in no way slows the access time of the right port. Both ports are
identical in function to standard CMOS Static RAM and can be read from,
or written to, at the same time with the only possible conflict arising from the
simultaneous writing of, or a simultaneous READ/WRITE of, a non-
semaphore location. Semaphores are protected against such ambiguous
situations and may be used by the system program to avoid any conflicts
in the non-semaphore portion of the Dual-Port RAM. These devices have
an automatic power-down feature controlled by CE the Dual-Port RAM
enable, and SEM, the semaphore enable. The CE and SEM pins control
on-chip power down circuitry that permits the respective port to go into
standby mode when not selected. This is the condition which is shown in
Truth Table II where CE and SEM are both HIGH.
or controllers and are typically very high-speed systems which are
software controlled or software intensive. These systems can benefit from
a performance increase offered by the IDT70V27's hardware sema-
phores, which provide a lockout mechanism without requiring complex
programming.
system flexibility by permitting shared resources to be allocated in varying
configurations. The IDT70V27 does not use its semaphore flags to control
any resources through hardware, thus allowing the system designer total
flexibility in system architecture.
methods of hardware arbitration is that wait states are never incurred in
either processor. This can prove to be a major advantage in very high-
speed systems.
How the Semaphore Flags Work
of the Dual-Port RAM. These latches can be used to pass a flag, or token,
from one port to the other to indicate that a shared resource is in use. The
semaphores provide a hardware assist for a use assignment method
called “Token Passing Allocation.” In this method, the state of a semaphore
latch is used as a token indicating that shared resource is in use. If the left
processor wants to use this resource, it requests the token by setting the
latch. This processor then verifies its success in setting the latch by reading
it. If it was successful, it proceeds to assume control over the shared
resource. If it was not successful in setting the latch, it determines that the
right side processor has set the latch first, has the token and is using the
shared resource. The left processor can then either repeatedly request
that semaphore’s status or remove its request for that semaphore to perform
another task and occasionally attempt again to gain control of the token via
the set and test sequence. Once the right side has relinquished the token,
the left side should succeed in gaining control.
The IDT70V27 is a fast Dual-Port 32K x 16 CMOS Static RAM with
The Dual-Port RAM features a fast access time, and both ports are
Systems which can best use the IDT70V27 contain multiple processors
Software handshaking between processors offers the maximum in
An advantage of using semaphores rather than the more common
The semaphore logic is a set of eight latches which are independent
Commercial and Industrial Temperature Range