ST72F264G ST Microelectronics, ST72F264G Datasheet - Page 78
ST72F264G
Manufacturer Part Number
ST72F264G
Description
(ST72F260G - ST72F264G) 8-BIT MCU
Manufacturer
ST Microelectronics
Datasheet
1.ST72F264G.pdf
(171 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ST72F264G2B5
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
ST72F264G2B6
Manufacturer:
ST
Quantity:
10
Company:
Part Number:
ST72F264G2B6
Manufacturer:
NEC
Quantity:
6 097
Part Number:
ST72F264G2B6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
ST72F264G2H1
Manufacturer:
CMD
Quantity:
1 020
Part Number:
ST72F264G2H1
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
ST72F264G2H1E
Manufacturer:
ST
Quantity:
50 000
Part Number:
ST72F264G2H1E
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
ST72F264G2M6
Manufacturer:
SCS
Quantity:
1 225
Part Number:
ST72F264G2M6
Manufacturer:
ST
Quantity:
20 000
www.DataSheet4U.com
DataSheet
ST72260G, ST72262G, ST72264G
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.4.4 Clock Phase and Clock Polarity
Four possible timing relationships may be chosen
by software, using the CPOL and CPHA bits (See
Figure
Note: The idle state of SCK must correspond to
the polarity selected in the SPICSR register (by
pulling up SCK if CPOL=1 or pulling down SCK if
CPOL=0).
The combination of the CPOL clock polarity and
CPHA (clock phase) bits selects the data capture
clock edge
Figure 51. Data Clock Timing Diagram
78/171
4
U
(from slave)
(from slave)
51).
(to slave)
(to slave)
(from master)
(from master)
MISO
MOSI
CAPTURE STROBE
SCK
(CPOL = 0)
MISO
MOSI
CAPTURE STROBE
SCK
(CPOL = 1)
SCK
(CPOL = 0)
SCK
(CPOL = 1)
SS
SS
.com
Note: This figure should not be used as a replacement for parametric information.
Refer to the Electrical Characteristics chapter.
MSBit
MSBit
MSBit
MSBit
Bit 6
Bit 6
Bit 6
Bit 6
www.DataSheet4U.com
Bit 5
Bit 5
Bit 5
Bit 5
CPHA =0
CPHA =1
Bit 4
Bit 4
Bit 4
Bit 4
Figure
combinations of the CPHA and CPOL bits. The di-
agram may be interpreted as a master or slave
timing diagram where the SCK pin, the MISO pin,
the MOSI pin are directly connected between the
master and the slave device.
Note: If CPOL is changed at the communication
byte boundaries, the SPI must be disabled by re-
setting the SPE bit.
Bit3
Bit3
Bit3
Bit3
51, shows an SPI transfer with the four
Bit 2
Bit 2
Bit 2
Bit 2
Bit 1
Bit 1
Bit 1
Bit 1
LSBit
LSBit
LSBit
LSBit
www.DataSheet
www.DataSheet
www.DataSheet
www.DataSheet4U
4U
4U.com
4U
.com
.com
.com