SAM9XE128 Atmel Corporation, SAM9XE128 Datasheet - Page 78
SAM9XE128
Manufacturer Part Number
SAM9XE128
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9260.pdf
(290 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9XE128.pdf
(860 pages)
4.SAM9XE128.pdf
(48 pages)
Specifications of SAM9XE128
Flash (kbytes)
128 Kbytes
Pin Count
217
Max. Operating Frequency
180 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
6
Ssc
1
Ethernet
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
Yes
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
312
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
16
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.65 to 1.95
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- SAM9260 PDF datasheet
- SAM9261 PDF datasheet #2
- SAM9XE128 PDF datasheet #3
- SAM9XE128 PDF datasheet #4
- Current page: 78 of 290
- Download datasheet (5Mb)
Memory Interface
4.1
4-2
About the memory interface
The ARM9E-S has a Harvard bus architecture with separate instruction and data
interfaces. This allows concurrent instruction and data accesses, and greatly reduces the
Cycles Per Instruction (CPI) of the processor. For optimal performance, single-cycle
memory accesses for both interfaces are required, although the core can be wait-stated
for nonsequential accesses, or slower memory systems.
For both instruction and data interfaces, the ARM9E-S processor core uses pipelined
addressing. This means that the address and control signals are generated the cycle
before the data transfer takes place. All memory accesses are timed with the clock
CLK.
For each interface there are different types of memory access:
•
•
•
•
The ARM9E-S can operate in both big-endian and little-endian memory configurations
and this is selected by the CFGBIGEND input. The endian configuration affects both
interfaces, so you must take care when designing the memory interface logic to allow
correct operation of the processor core.
For system programming purposes, you must normally provide some mechanism for
the data interface to access instruction memory. There are two main reasons for this:
•
•
A typical implementation of an ARM9E-S based cached processor has Harvard caches
and a unified memory structure beyond the caches, therefore giving the data interface
access to the instruction memory space. However, for an SRAM-based system, you
cannot use this technique, and you must use an alternative method.
It is not necessary for the instruction interface to have access to the data memory area
unless the processor needs to execute code from data memory.
Nonsequential
Sequential
Internal
Coprocessor transfer (for the data interface).
The use of in-line data for literal pools is very common. This data is fetched using
the data interface but is normally contained in the instruction memory space.
To enable debug using the JTAG interface it must be possible to download code
into the instruction memory. This code has to be written to memory through the
data interface, because the instruction interface is read-only. In this case it is
essential for the data interface to have access to the instruction memory.
Copyright © 2000 ARM Limited. All rights reserved.
ARM DDI 0165B
Related parts for SAM9XE128
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: