ATtiny2313A Atmel Corporation, ATtiny2313A Datasheet - Page 33

• Manufacturer Part Number: ATtiny2313A
• Manufacturer: Atmel Corporation

Specifications of ATtiny2313A

• Flash (kbytes): 2 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 18
• Ext Interrupts: 18
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

8246B–AVR–09/11
the CLKPCE bit within this time-out period does neither extend the time-out period, nor clear the
CLKPCE bit.
• Bits 6:4 – Res: Reserved Bits
These bits are reserved bits in the ATtiny2313A/4313 and will always read as zero.
• Bits 3:0 – CLKPS3:0: Clock Prescaler Select Bits 3 - 0
These bits define the division factor between the selected clock source and the internal system
clock. These bits can be written run-time to vary the clock frequency to suit the application
requirements. As the divider divides the master clock input to the MCU, the speed of all synchro-
nous peripherals is reduced when a division factor is used. The division factors are given in
Table 6-8 on page
To avoid unintentional changes of clock frequency, a special write procedure must be followed
to change the CLKPS bits:
Interrupts must be disabled when changing prescaler setting to make sure the write procedure is
not interrupted. The Application software must ensure that a sufficient division factor is chosen if
the selected clock source has a higher frequency than the maximum frequency of the device at
the present operating conditions. The device is shipped with the CKDIV8 fuse programmed.
Table 6-8.
1. Write the Clock Prescaler Change Enable (CLKPCE) bit to one and all other bits in
2. Within four cycles, write the desired value to CLKPS while writing a zero to CLKPCE.
CLKPS3
CLKPR to zero.
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Clock Prescaler Select
33.
CLKPS2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
CLKPS1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
CLKPS0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
ATtiny2313A/4313
Clock Division Factor
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
128
256
16
32
64
1
2
4
8
33