ATmega16M1 Atmel Corporation, ATmega16M1 Datasheet - Page 183

• Manufacturer Part Number: ATmega16M1
• Manufacturer: Atmel Corporation

Specifications of ATmega16M1

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

19.10.3
8209D–AVR–11/10
CANGIT – CAN General Interrupt Register
• Bit 2 – ENFG: Enable Flag
This flag does not generate an interrupt.
• Bit 1 – BOFF: Bus Off Mode
BOFF gives the information of the state of the CAN channel. Only entering in bus off mode gen-
erates the BOFFIT interrupt.
• Bit 0 – ERRP: Error Passive Mode
ERRP gives the information of the state of the CAN channel. This flag does not generate an
interrupt.
• Bit 7 – CANIT: General Interrupt Flag
This is a read only bit.
• Bit 6 – BOFFIT: Bus Off Interrupt Flag
Writing a logical one resets this interrupt flag. BOFFIT flag is only set when the CAN enters in
bus off mode (coming from error passive mode).
• Bit 5 – OVRTIM: Overrun CAN Timer
Writing a logical one resets this interrupt flag. Entering in CAN timer overrun interrupt handler
also reset this interrupt flag
• Bit 4 – BXOK: Frame Buffer Receive Interrupt
Writing a logical one resets this interrupt flag. BXOK flag can be cleared only if all CONMOB
fields of the MOb’s of the buffer have been re-written before.
Initial Value
Read/Write
– 0 - CAN controller disable: because an enable/standby command is not immediately
– 1 - CAN controller enable
– 0 - no bus off mode
– 1 - bus off mode
– 0 - no error passive mode
– 1 - error passive mode
– 0 - no interrupt
– 1 - CAN interrupt: image of all the CAN controller interrupts except for OVRTIM
– 0 - no interrupt
– 1 - bus off interrupt when the CAN enters in bus off mode
– 0 - no interrupt
– 1 - CAN timer overrun interrupt: set when the CAN timer switches from 0xFFFF to 0
Bit
effective, this status gives the true state of the chosen mode
interrupt. This bit can be used for polling method
CANIT
R
7
0
BOFFIT
R/W
6
0
OVRTIM
R/W
5
0
BXOK
R/W
4
0
ATmega16M1/32M1/64M1
SERG
R/W
3
0
CERG
R/W
2
0
FERG
R/W
1
0
AERG
R/W
0
0
CANGIT
183