ATmega16A Atmel Corporation, ATmega16A Datasheet - Page 40
ATmega16A
Manufacturer Part Number
ATmega16A
Description
Manufacturer
Atmel Corporation
Specifications of ATmega16A
Flash (kbytes)
16 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
32
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATmega16A-AU
Manufacturer:
HIROSE
Quantity:
3 000
Part Number:
ATmega16A-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega16A-AUR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
ATmega16A-PU
Manufacturer:
AT
Quantity:
20 000
Part Number:
ATmega16A-U-TH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega16AU-TH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
10.1.5
10.2
10.2.1
40
Internal Voltage Reference
ATmega16A
Watchdog Reset
Voltage Reference Enable Signals and Start-up Time
Figure 10-5. Brown-out Reset During Operation
When the Watchdog times out, it will generate a short reset pulse of one CK cycle duration. On
the falling edge of this pulse, the delay timer starts counting the Time-out period t
details, refer to
Figure 10-6. Watchdog Reset During Operation
ATmega16A features an internal bandgap reference. This reference is used for Brown-out
Detection, and it can be used as an input to the Analog Comparator or the ADC. The 2.56V ref-
erence to the ADC is generated from the internal bandgap reference.
The voltage reference has a start-up time that may influence the way it should be used. The
start-up time is given in
reference is not always turned on. The reference is on during the following situations:
Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC, the user
must always allow the reference to start up before the output from the Analog Comparator or
1. When the BOD is enabled (by programming the BODEN Fuse).
2. When the bandgap reference is connected to the Analog Comparator (by setting the
3. When the ADC is enabled.
ACBG bit in ACSR).
CC
“Watchdog Timer” on page
INTERNAL
TIME-OUT
RESET
RESET
V
CC
“System and Reset Characteristics” on page
V
CK
BOT-
41.
V
t
TOUT
BOT+
296. To save power, the
8154B–AVR–07/09
TOUT
. For