ATmega16A Atmel Corporation, ATmega16A Datasheet - Page 265

• Manufacturer Part Number: ATmega16A
• Manufacturer: Atmel Corporation

Specifications of ATmega16A

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.2
8154B–AVR–07/09
Fuse Bits
Table 26-2.
Notes:
The ATmega16A has two fuse bytes.
of all the fuses and how they are mapped into the fuse bytes. Note that the fuses are read as
logical zero, “0”, if they are programmed.
Table 26-3.
Notes:
Fuse High
Byte
OCDEN
JTAGEN
SPIEN
CKOPT
EESAVE
BOOTSZ1
BOOTSZ0
BOOTRST
BLB1 Mode
4
1
2
3
4
(1)
1. Program the Fuse bits before programming the Lock bits.
2. “1” means unprogrammed, “0” means programmed
1. The SPIEN Fuse is not accessible in SPI Serial Programming mode.
2. The CKOPT Fuse functionality depends on the setting of the CKSEL bits. See
3. The default value of BOOTSZ1:0 results in maximum Boot Size. See
Memory Lock Bits
(2)
(4)
(5)
Sources” on page 25.
Lock Bit Protection Modes (Continued)
Fuse High Byte
Bit No.
BLB12
7
6
5
4
3
2
1
0
0
1
1
0
0
Description
Enable OCD
Enable JTAG
Enable SPI Serial Program and
Data Downloading
Oscillator options
EEPROM memory is preserved
through the Chip Erase
Select Boot Size (see
for details)
Select Boot Size (see
for details)
Select reset vector
(2)
BLB11
1
1
0
0
1
for details.
Protection Type
LPM executing from the Boot Loader section is not allowed to
read from the Application section. If interrupt vectors are placed
in the Boot Loader section, interrupts are disabled while
executing from the Application section.
No restrictions for SPM or LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section, and LPM
executing from the Application section is not allowed to read
from the Boot Loader section. If interrupt vectors are placed in
the Application section, interrupts are disabled while executing
from the Boot Loader section.
LPM executing from the Application section is not allowed to
read from the Boot Loader section. If interrupt vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
Table 26-3
Table 25-6
Table 25-6
and
Table 26-4
1 (unprogrammed)
0 (programmed)
0 (programmed)
Default Value
1 (unprogrammed, OCD disabled)
0 (programmed, JTAG enabled)
0 (programmed, SPI prog. enabled)
1 (unprogrammed, EEPROM not
preserved)
1 (unprogrammed)
describe briefly the functionality
ATmega16A
Table 25-6 on page
(3)
(3)
See “Clock
262.
265