ATmega16 Atmel Corporation, ATmega16 Datasheet - Page 260

• Manufacturer Part Number: ATmega16
• Manufacturer: Atmel Corporation

Specifications of ATmega16

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Fuse Bits
2466T–AVR–07/10
Table 104. Lock Bit Protection Modes (Continued)
Notes:
The ATmega16 has two fuse bytes.
all the fuses and how they are mapped into the fuse bytes. Note that the fuses are read as logi-
cal zero, “0”, if they are programmed.
Table 105. Fuse High Byte
Notes:
BLB1 Mode
Fuse High
Byte
OCDEN
JTAGEN
SPIEN
CKOPT
EESAVE
BOOTSZ1
BOOTSZ0
BOOTRST
1
2
3
4
Memory Lock Bits
(1)
1. Program the Fuse bits before programming the Lock bits.
2. “1” means unprogrammed, “0” means programmed
1. The SPIEN Fuse is not accessible in SPI Serial Programming mode.
2. The CKOPT Fuse functionality depends on the setting of the CKSEL bits. See
3. The default value of BOOTSZ1..0 results in maximum Boot Size. See
4. Never ship a product with the OCDEN Fuse programmed regardless of the setting of Lock bits
5. If the JTAG interface is left unconnected, the JTAGEN fuse should if possible be disabled. This
(2)
(4)
(5)
Sources” on page 25.
and the JTAGEN Fuse. A programmed OCDEN Fuse enables some parts of the clock system
to be running in all sleep modes. This may increase the power consumption.
to avoid static current at the TDO pin in the JTAG interface.
No.
BLB12
Bit
7
6
5
4
3
2
1
0
1
1
0
0
Description
Enable OCD
Enable JTAG
Enable SPI Serial Program and
Data Downloading
Oscillator options
EEPROM memory is preserved
through the Chip Erase
Select Boot Size (see
for details)
Select Boot Size (see
for details)
Select reset vector
(2)
BLB11
1
0
0
1
for details.
Protection Type
No restrictions for SPM or LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section,
and LPM executing from the Application section is not
allowed to read from the Boot Loader section. If interrupt
vectors are placed in the Application section, interrupts
are disabled while executing from the Boot Loader section.
LPM executing from the Application section is not allowed
to read from the Boot Loader section. If interrupt vectors
are placed in the Application section, interrupts are
disabled while executing from the Boot Loader section.
Table 105
Table 100
Table 100
and
Table 106
Default Value
1 (unprogrammed, OCD disabled)
0 (programmed, JTAG enabled)
0 (programmed, SPI prog. enabled)
1 (unprogrammed)
1 (unprogrammed, EEPROM not
preserved)
0 (programmed)
0 (programmed)
1 (unprogrammed)
describe briefly the functionality of
(3)
(3)
ATmega16(L)
Table 100 on page
See “Clock
257.
260