AT89LP3240 Atmel Corporation, AT89LP3240 Datasheet - Page 135
AT89LP3240
Manufacturer Part Number
AT89LP3240
Description
Manufacturer
Atmel Corporation
Datasheet
1.AT89LP3240.pdf
(200 pages)
Specifications of AT89LP3240
Flash (kbytes)
32 Kbytes
Max. Operating Frequency
20 MHz
Cpu
8051-1C
Max I/o Pins
38
Spi
1
Twi (i2c)
1
Uart
1
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
153.8
Sram (kbytes)
4.25
Eeprom (bytes)
8192
Self Program Memory
IAP
Operating Voltage (vcc)
2.4 to 3.6
Timers
3
Isp
SPI/OCD
Watchdog
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 135 of 200
- Download datasheet (7Mb)
20.1
3706C–MICRO–2/11
ADC Operation
The ADC converts an analog input voltage to a 10-bit signed digital value through successive
approximation. When DIFF (DADI.3) is zero, the ADC operates in single-ended mode and the
input voltage is the difference between the voltage at the input pin and V
mode (DIFF = 1) the input voltage is the difference between the positive and negative input pins.
The minimum value represents zero difference and the maximum values represent a difference
of positive or negative V
The analog input channel is selected by writing to the ACS bits in DADI. Any of the eight Port 0
input pins can be selected as single-ended inputs to the ADC. Four pairs of Port 0 pins can be
selected as differential inputs. The ACON bit (DADI.7) must be set to one to connect the input
pins to the ADC. Prior to changing ACS, ACON must be cleared to zero. This ensures that
crosstalk between channels is limited. ACON must be set back to one after ACS is updated.
ACON and ACS should not be changed while a conversion is in progress. ADC input channels
must have their port pins configured for input-only mode.
The ADC is enabled by setting the ADCE bit in DADC. Some settling time is required for the ref-
erence circuits to stabilize after the ADC is enabled. The ADC does not consume power when
ADCE is cleared, so it is recommended to switch off the ADC before entering power saving
modes.
A timing diagram of an ADC conversion is shown in
ADC clock cycles to complete. The analog input is sampled during the third cycle of the conver-
sion and is held constant for the remainder of the conversion. At the end of the conversion, the
interrupt flag, ADIF, is set and the result is written to the data registers. An additional 1 ADC
clock cycle and up to 2 system clock cycles may be required to synchronize ADIF with the rest of
the system. The results in DADH/DADL remain valid until the next conversion completes. DADH
and DADL are read-only registers during ADC mode.
Figure 20-2. ADC Timing Diagram
The equivalent model for the analog input circuitry is illustrated in
applied to ADCn is subjected to the pin capacitance and input leakage of that pin, regardless of
whether that channel is selected as input to the ADC. When the channel is selected, the source
must drive the S/H capacitor through the series resistance (combined resistance in the input
path). To achieve 10-bit resolution the S/H capacitor must be charged to within 1/2 LSB of the
expected value within the 1 ADC clock period sample time. High impedance sources may
require a reduction in the ADC clock frequency to achieve full resolution.
Cycle Number
ADC Clock
GO/BSY
ADIF
DADH
DADL
1
2
Initialize Circuitry
REF
3
minus 1 LSB.
4
5
Sample & Hold
One Conversion
6
7
8
Figure
9
10
Conversion
Complete
20-2. The conversion requires 13
AT89LP3240/6440
11
Figure
12
13
20-3. An analog source
DD
MSB of Result
LSB of Result
/2. In differential
Next Conversion
1
2
Initialize
3
135
Related parts for AT89LP3240
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-Bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: