AT89C51IC2 Atmel Corporation, AT89C51IC2 Datasheet - Page 76
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT89C51IC2
Manufacturer Part Number
AT89C51IC2
Description
Manufacturer
Atmel Corporation
Specifications of AT89C51IC2
Flash (kbytes)
32 Kbytes
Max. Operating Frequency
60 MHz
Cpu
8051-12C
Max I/o Pins
34
Spi
1
Twi (i2c)
1
Uart
1
Sram (kbytes)
1.25
Self Program Memory
API
Operating Voltage (vcc)
2.7 to 5.5
Timers
4
Isp
UART
Watchdog
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT89C51IC2-RLTIL
Manufacturer:
ATMEL
Quantity:
640
Company:
Part Number:
AT89C51IC2-RLTIL
Manufacturer:
ATMEL
Quantity:
4 116
Company:
Part Number:
AT89C51IC2-UL
Manufacturer:
XR
Quantity:
2
Company:
Part Number:
AT89C51IC2-UM
Manufacturer:
Atmel
Quantity:
5
Error Conditions
Mode Fault (MODF)
Write Collision (WCOL)
Overrun Condition
SS Error Flag (SSERR)
Interrupts
76
AT89C51IC2
The following flags in the SPSTA signal SPI error conditions:
Mode Fault error in Master mode SPI indicates that the level on the Slave Select (SS)
pin is inconsistent with the actual mode of the device. MODF is set to warn that there
may be a multi-master conflict for system control. In this case, the SPI system is
affected in the following ways:
•
•
•
When SS Disable (SSDIS) bit in the SPCON register is cleared, the MODF flag is set
when the SS signal becomes ’0’.
However, as stated before, for a system with one Master, if the SS pin of the Master
device is pulled low, there is no way that another Master attempts to drive the network.
In this case, to prevent the MODF flag from being set, software can set the SSDIS bit in
the SPCON register and therefore making the SS pin as a general-purpose I/O pin.
Clearing the MODF bit is accomplished by a read of SPSTA register with MODF bit set,
followed by a write to the SPCON register. SPEN Control bit may be restored to its orig-
inal set state after the MODF bit has been cleared.
A Write Collision (WCOL) flag in the SPSTA is set when a write to the SPDAT register is
done during a transmit sequence.
WCOL does not cause an interruption, and the transfer continues uninterrupted.
Clearing the WCOL bit is done through a software sequence of an access to SPSTA
and an access to SPDAT.
An overrun condition occurs when the Master device tries to send several data Bytes
and the Slave devise has not cleared the SPIF bit issuing from the previous data Byte
transmitted. In this case, the receiver buffer contains the Byte sent after the SPIF bit was
last cleared. A read of the SPDAT returns this Byte. All others Bytes are lost.
This condition is not detected by the SPI peripheral.
A Synchronous Serial Slave Error occurs when SS goes high before the end of a
received data in slave mode. SSERR does not cause in interruption, this bit is cleared
by writing 0 to SPEN bit (reset of the SPI state machine).
Two SPI status flags can generate a CPU interrupt requests:
Table 57. SPI Interrupts
Serial Peripheral data transfer flag, SPIF: This bit is set by hardware when a transfer
has been completed. SPIF bit generates transmitter CPU interrupt requests.
Mode Fault flag, MODF: This bit becomes set to indicate that the level on the SS is
inconsistent with the mode of the SPI. MODF with SSDIS reset, generates receiver/error
CPU interrupt requests. When SSDIS is set, no MODF interrupt request is generated.
Figure 32 gives a logical view of the above statements.
Flag
SPIF (SP data transfer)
MODF (Mode Fault)
An SPI receiver/error CPU interrupt request is generated
The SPEN bit in SPCON is cleared. This disables the SPI
The MSTR bit in SPCON is cleared
Request
SPI Transmitter Interrupt request
SPI Receiver/Error Interrupt Request (if SSDIS = ’0’)
4301D–8051–02/08