AT32UC3B064 Atmel Corporation, AT32UC3B064 Datasheet - Page 321

• Manufacturer Part Number: AT32UC3B064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B064

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.6.6.3
Figure 21-34. IrDA Demodulator Operations
21.6.7
32059L–AVR32–01/2012
CLK_USART
Receiver
Counter
Value
Input
RXD
RS485 Mode
IrDA Demodulator
6
5
4
Rejected
Table 21-11. IrDA Baud Rate Error (Continued)
The demodulator depends on an 8-bit down counter loaded with the value in IRDA_Filter field in
the IrDA Filter Register (IFR.IRDA_FILTER). When a falling edge on RXD is detected, the coun-
ter starts decrementing at CLK_USART speed. If a rising edge is detected on RXD, the counter
stops and is reloaded with the IFR value. If no rising edge has been detected when the counter
reaches zero, the receiver input is pulled low during one bit period. See
one to the Infrared Receive Line Filter bit (MR.FILTER), enables a noise filter that, instead of
using just one sample, will choose the majority value from three consecutive samples.
The USART features an RS485 mode, supporting line driver control. This supplements normal
synchronous and asynchronous mode by driving the RTS pin high when the transmitter is oper-
ating. The RTS pin level is the inverse of the CSR.TXEMPTY value. Writing 0x1 to MR.MODE
enables this mode. A typical connection to a RS485 bus is shown in
Figure 21-35. Typical Connection to a RS485 Bus
If a timeguard has been configured the RTS pin will remain high for the duration specified in TG,
as shown in
Pulse
Peripheral Clock
3 686 400
20 000 000
32 768 000
3
2
6
Figure
6
21-36.
5
Baud Rate
4
2 400
2 400
2 400
USART
3
2
RXD
TXD
RTS
1
0
Accepted
Pulse
521
853
CD
96
Driven Low During 16 Baud Rate Clock Cycles
Baud Rate Error
0.00%
0.03%
0.04%
Differential
Bus
Figure
Figure
21-35.
Pulse Time
21-34. Writing a
78.13
78.13
78.13
321