AT32UC3B064 Atmel Corporation, AT32UC3B064 Datasheet - Page 239

• Manufacturer Part Number: AT32UC3B064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B064

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 19-24. Read Access Ordered by a MASTER
19.13.5.2
Figure 19-25. Write Access Ordered by a Master
32059L–AVR32–01/2012
EOSVACC
EOSVACC
SVREAD
SVREAD
TXRDY
SVACC
RXRDY
SVACC
NACK
TWD
TWD
Write Operation
S
S
ADR
ADR
TWI answers with a NACK
TWI answers with a NACK
SADR does not match,
SADR does not match,
Notes:
The write mode is defined as a data transmission from the master.
After a START or a REPEATED START, the decoding of the address starts. If the slave address
is decoded, SVACC is set and SVREAD indicates the direction of the transfer (SVREAD is low in
this case).
Until a STOP or REPEATED START condition is detected, TWI stores the received data in the
RHR register.
If a STOP condition or a REPEATED START + an address different from SADR is detected,
SVACC is reset.
Figure 19-25 on page 239
Notes:
W
R
NA
NA
1. When SVACC is low, the state of SVREAD becomes irrelevant.
2. TXRDY is reset when data has been transmitted from THR to the shift register and set when
1. When SVACC is low, the state of SVREAD becomes irrelevant.
2. RXRDY is set when data has been transmitted from the shift register to the RHR and reset
DATA
DATA
this data has been acknowledged or non acknowledged.
when this data is read.
NA
NA
P/S/Sr
P/S/Sr
describes the Write operation.
Write THR
SADR
SADR
TWI answers with an ACK
TWI answers with an ACK
SADR matches,
SADR matches,
W A
R
SVREAD has to be taken into account only while SVACC is active
SVREAD has to be taken into account only while SVACC is active
A
DATA
DATA
A
A
Read RHR
ACK/NACK from the Master
A
A
DATA NA S/Sr
DATA
NA
S/Sr
Read RHR
239