AT32UC3A0512AU Atmel Corporation, AT32UC3A0512AU Datasheet - Page 151

• Manufacturer Part Number: AT32UC3A0512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A0512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 109
• Ext Interrupts: 109
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
20.6
20.6.1
20.6.2
20.6.3
20.7
20.7.1
20.7.2
Product Dependencies
Functional Description
I/O Lines
Power Management
Interrupt
Bus Multiplexing
Pull-up Control
The pins used for interfacing the External Bus Interface may be multiplexed with the GPIO lines.
The programmer must first program the GPIO controller to assign the External Bus Interface
pins to their peripheral function. If I/O lines of the External Bus Interface are not used by the
application, they can be used for other purposes by the GPIO Controller.
The EBI HSB clock and SDRAMC, SMC and ECC PB clocks are generated by the Power Man-
ager. Before using the EBI, the programmer must ensure that these clocks are enabled in the
Power Manager.
To prevent bus errors EBI operation must be terminated before entering sleep mode
The EBI interface has an interrupt line connected to the Interrupt Controller. Handling the EBI
interrupt requires programming the interrupt controller before configuring the EBI.
The EBI transfers data between the internal HSB Bus (handled by the HMatrix) and the external
memories or peripheral devices. It controls the waveforms and the parameters of the external
address, data and control busses and is composed of the following elements:
• The Static Memory Controller (SMC)
• The SDRAM Controller (SDRAMC)
• A chip select assignment feature that assigns an HSB address space to the external devices
• A multiplex controller circuit that shares the pins between the different Memory Controllers
The EBI offers a complete set of control signals that share the 16-bit data lines, the address
lines of up to 24 bits and the control signals through a multiplex logic operating in function of the
memory area requests.
Multiplexing is specifically organized in order to guarantee the maintenance of the address and
output control lines at a stable state while no external access is being performed. Multiplexing is
also designed to respect the data float times defined in the Memory Controllers. Furthermore,
refresh cycles of the SDRAM are executed independently by the SDRAM Controller without
delaying the other external Memory Controller accesses.
A specific HMATRIX_SFR register in the Matrix User Interface permit enabling of on-chip pull-up
resistors on the data bus lines not multiplexed with the GPIO Controller lines. For details on this
register, refer to the Peripherals Section. The pull-up resistors are enabled after reset. Setting
the EBI_DBPUC bit disables the pull-up resistors on lines not muxed with GPIO. Enabling the
pull-up resistor on lines multiplexed with GPIO lines can be performed by programming the
appropriate GPIO controller.
AT32UC3A
151