DS3171N+ Maxim Integrated Products, DS3171N+ Datasheet - Page 76

• Manufacturer Part Number: DS3171N+
• Description: TXRX SGL DS3/E3 400PBGA
• Manufacturer: Maxim Integrated Products

Specifications of DS3171N+

• Function: Single-Chip Transceiver
• Interface: DS3, E3
• Number Of Circuits: 1
• Voltage - Supply: 3.135 V ~ 3.465 V
• Current - Supply: 273mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 400-BGA
• Includes: DS3 Framers, E3 Framers, HDLC Controller, On-Chip BERTs
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power (watts): -
• Other names: 90-31710+N00

Table 10-24. RCLKOn/RGCLKn Output Pin Functions
FM[2:0]
PORT.CR2
0XX (FSCT)
0XX (FSCT)
1XX (FBM)
10.5.9 Framing Modes
The framing modes are selected independently of the line interface modes using the PORT.CR2.FM[2:0] control
bits. Different blocks are used in different framing modes. The bit error test (BERT) function can be enabled in any
mode. The LIU, JA and line encoder/decoder blocks are selected by the line mode (LM[2:0]) code.
Table 10-25. Framing Mode Select Bits FM[2:0]
10.5.10 Line Interface Modes
The line interface modes can be selected semi-independently of the framing modes using the PORT.CR2.LM[2:0]
control bits. The major blocks controlled are the transmit LIU (TX LIU), receive LIU (RX LIU), jitter attenuator (JA)
and the line encoder/decoder. The line encoder/decoder is used for B3ZS, HDB3 and AMI line interface encoding
modes. The line encoder-decoder block is not used for line encoding or decoding in the UNI mode but the BPV
counter in it can be used to count external pulses on the RNEGn / RCLVn pin. The jitter attenuator (JA) can be off
(OFF) or put in either the transmit (TX) or receive (RX) path with the TX LIU or RX LIU. Both TX LIU and RX LIU
can be enabled (ON) or disabled (OFF).
The “Analog Loop Back” (ALB) is available when the LIU is enabled or disabled. It is an actual loop back of the
analog positive and negative pulses from the TX LIU to the RX LIU when the LIU is enabled. If the LIU is disabled,
it is a digital loop back of the TLCLK, TPOS, TNEG signals to the RLCLK, RPOS and RNEG signals.
When the line is configured for B3ZS/HDB3/AMI line codes, the line codes are determined by the framing mode
and the TZCDS and RZCDS bits control the AMI line mode selection bits in the line encoder/decoder blocks. The
DS3 modes select the B3ZS line coding, the E3 modes select the HDB3 line codes. Refer to
configuration.
FM[2:0]
11X
000
001
010
011
100
Description
DS3 C-bit Framed
DS3 M13 Framed
E3 G.751 Framed
E3 G.832 Framed
DS3 Rate Clear Channel
E3 Rate Clear Channel
RCLKS
PORT.CR3
X
0
1
Pin function
RGCLKn
RCLKOn
RCLKOn
Gap source
RDENn
none
none
HDB3/AMI/UNI
Line Code
B3ZS/AMI/UNI
B3ZS/AMI/UNI
HDB3/AMI/UNI
HDB3/AMI/UNI
B3ZS/AMI/UNI
76
Figure
Figure 6-1
Figure 6-1
Figure 6-1
Figure 6-1
Figure 6-2
Figure 6-2
Table 10-26
for