NOII4SM6600A-QDC ON Semiconductor, NOII4SM6600A-QDC Datasheet - Page 6

• Manufacturer Part Number: NOII4SM6600A-QDC
• Manufacturer: ON Semiconductor

Specifications of NOII4SM6600A-QDC

• Lead Free Status / Rohs Status: Supplier Unconfirmed

Electrical Specifications
Table 2. Recommended Operating Ratings
Table 3. Absolute Maximum Ratings
All parameters are characterized for DC conditions after thermal equilibrium is established. Unused inputs must always be tied to an
appropriate logic level, for example, V
it has no power supply filtering on chip. Therefore, all power supplies to the sensor must be clean with the target being to achieve a
low noise (1 mV). Special attention must be given to the pixel supplies VPIX, GND_AB, VRESET and VRESET_DS.
Table 4. Recommended DC Operating Conditions
VDD_PIX
VDD_RESET
VDD_RESET_DS
VDDA
VDDA_ADC
VDDAMP
VDDD
VDDD_ADC
Notes
Electrostatic discharge
1. Operating ratings are conditions in which operation of the device is intended to be functional. All parameters are characterized for DC conditions after thermal
2. Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These
3. This device does NOT contains circuitry to protect the inputs against damage caused by high static voltages or electric fields. ON Semiconductor recommends that
4. The IBIS4-6600 does not have latchup protection.
5. V
equilibrium is established. Unused inputs must always be tied to an appropriate logic level, for example, VDD or GND.
are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied.
customers become familiar with, and follow the procedures in JEDEC Standard JESD625-A. Refer to Application Note AN52561.
DD
Parameter
= V
Symbol
(ESD)
Symbol
V
V
%RH
LU
T
DDD
V
DD
OUT
T
T
ST
IN
S
[4]
J
[5]
= V
[3]
DDA
(V
DDD
is supply to digital circuit, V
DC Supply Voltage
DC Input Voltage
DC Output Voltage
Storage Temperature
Humidity (Relative)
Human Body Model (HBM)
Charged Device Model (CDM)
Latch-up
V
Reset voltage. Highest voltage to the chip. 3.3V for
extended dynamic range or 'hard reset'
Variable reset voltage (dual slope)
V
Analog supply to the ADC
V
V
Digital supply to the ADC
Operating temperature range
Storage temperature range
Storage humidity range
DD
DD
DD
DD
of pixel core
of analog supply
of analog output. (Can be connected to V
of digital supply
DD
[2], [3] [4]
or GND. The IBIS4-6600 is extremely susceptible to noise on the power supplies. In addition,
[1,3]
DDA
Rev. 9 | www.onsemi.com | Page 6 of 32
Description
Parameter
to analog circuit).
Description
DDA
)
Dynamic
Currents
Typical
53mA
20mA
10mA
3mA
3mA
–0.5
–0.5
–0.5
Min
–30
-
See Note 3
See Note 4
Min
-5%
-5%
-5%
-5%
-5%
-5%
-5%
-5%
Min
-30
20
30
85% at 85 °C
(V
(V
NOII4SM6600A
DD
DD
Max
+85
4.3
+ 0.5)
+ 0.5)
Typ (V)
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
Max
65
40
60
Units
%RH
Unit
3.3V
Max
mA
5%
5%
5%
5%
5%
5%
5%
°C
C
C
V
V
V
V