EVAL-ADF7023-JDB2Z Analog Devices Inc, EVAL-ADF7023-JDB2Z Datasheet - Page 90

• Manufacturer Part Number: EVAL-ADF7023-JDB2Z
• Description: BOARD EVAL ADF7023-JDB2Z
• Manufacturer: Analog Devices Inc
• Series: -r
• Type: Transceiverr

Specifications of EVAL-ADF7023-JDB2Z

• Frequency: 902MHz ~ 958MHz
• Kit Application Type: Wireless Connectivity
• Application Sub Type: RF Transceiver
• Features: Operating At RF Band 902MHz To 958MHz, PC Interface And Control
• Silicon Manufacturer: Analog Devices
• Silicon Core Number: ADF7023
• Kit Contents: Board, Manual
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: ADF7023

ADF7023-J
MCR REGISTER DESCRIPTION
The MCR register settings are not retained when the device enters the PHY_SLEEP state.
Table 96. 0x307: PA_LEVEL_MCR
Bit
[5:0]
Table 97. 0x30C: WUC_CONFIG_HIGH
Bit
[7]
[6]
[5]
[4]
[3]
[2:0]
Register WUC_CONFIG_LOW should never be written to without updating Register WUC_CONFIG_HIGH first.
Table 98. 0x30D: WUC_CONFIG_LOW
Bit
[7]
[6]
[5]
[4]
[3]
[2:1]
[0]
Updates to Register WUC_VALUE_HIGH become effective only after Register WUC_VALUE_LOW is written to.
Table 99. 0x30E: WUC_VALUE_HIGH
Bit
[7:0]
Name
WUC_TIMER_VALUE[15:8]
Name
Reserved
WUC_RCOSC_EN
WUC_XOSC32K_EN
WUC_CLKSEL
WUC_BBRAM_EN
Reserved
WUC_ARM
Name
PA_LEVEL_MCR
Name
Reserved
WUC_BGAP
WUC_LDO_SYNTH
WUC_LDO_DIG
WUC_XTO26M_EN
WUC_PRESCALER
R/W
W
W
W
W
W
W
W
W
W
W
W
R/W
W
R/W
R/W
R/W
W
W
Reset
0
Reset
0
0
0
0
0
0
Reset
0
0
0
0
0
0
0
Reset
0
Rev. 0 | Page 90 of 100
Description
Power amplifier level. If PA ramp is enabled, the PA ramps to this target
level. The PA level can be set in the 0 to 63 range. The PA level (with less
resolution) can also be set via the BBRAM; therefore, the MCR setting
should be used only if more resolution is required.
Description
Set to 0
Set to 0
Set to 0
Set to 0
Set to 0
WUC_PRESCALER
0
1
2
3
4
5
6
7
1: enable RCOSC32K
1: enable XOSC32K
Select the WUC timer clock source
1: enable wake-up on a WUC timeout event
Description
WUC timer reload value, Bits[15:8] of [15:0]. A wake-up event is triggered
when the WUC unit is enabled and the timer has counted down to 0. The
timer is clocked with the prescaler output rate. An update to this register
becomes effective only after WUC_VALUE_LOW is written. See Table 100.
Description
Set to 0
0: disable RCOSC32K
0: disable XOSC32K
1: RC 32.768 kHz oscillator
0: external crystal oscillator
1: enable power to the BBRAM during the PHY_SLEEP state
0: disable power to the BBRAM during the PHY_SLEEP state
Set to 0
0: disable wake-up on a WUC timeout event
32.768 kHz Divider
1
4
8
16
128
1034
81 2
65,536
Tick Period
30.52 μs
122.1 μs
244.1 μs
488.3 μs
3.91 ms
31.25 ms
250 ms
2000 ms