PIC18F45J10-I/ML Microchip Technology Inc., PIC18F45J10-I/ML Datasheet - Page 227

• Manufacturer Part Number: PIC18F45J10-I/ML
• Description: 44 PIN, 32 KB FLASH, 1024 RAM
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F45J10-I/ML

• A/d Inputs: 13-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 32
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin QFN
• Programmable Memory: 32K Bytes
• Ram Size: 1K Bytes
• Speed: 40 MHz
• Timers: 1-8 bit, 2-16 bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

19.0
The comparator voltage reference is a 16-tap resistor
ladder network that provides a selectable reference
voltage. Although its primary purpose is to provide a
reference for the analog comparators, it may also be
used independently of them.
A block diagram of the module is shown in Figure 19-1.
The resistor ladder is segmented to provide two ranges
of CV
conserve power when the reference is not being used.
The module’s supply reference can be provided from
either device V
19.1
The voltage reference module is controlled through the
CVRCON register (Register 19-1). The comparator
voltage reference provides two ranges of output
voltage, each with 16 distinct levels. The range to be
REGISTER 19-1:
© 2006 Microchip Technology Inc.
REF
COMPARATOR VOLTAGE
REFERENCE MODULE
Configuring the Comparator
Voltage Reference
values and has a power-down function to
bit 7
bit 6
bit 5
bit 4
bit 3-0
DD
/V
SS
or an external voltage reference.
CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER
bit 7
Legend:
R = Readable bit
-n = Value at POR
CVREN: Comparator Voltage Reference Enable bit
1 = CV
0 = CV
CVROE: Comparator V
1 = CV
0 = CV
CVRR: Comparator V
1 = 0 to 0.667 CV
0 = 0.25 CV
CVRSS: Comparator V
1 = Comparator reference source, CV
0 = Comparator reference source, CV
CVR3:CVR0: Comparator V
When CVRR = 1:
CV
When CVRR = 0:
CV
CVREN
R/W-0
Note 1: CVROE overrides the TRISA<2> bit setting.
REF
REF
= ((CVR3:CVR0)/24) • (CV
= (CV
REF
REF
REF
REF
CVROE
circuit powered on
circuit powered down
voltage level is also output on the RA2/AN2/V
voltage is disconnected from the RA2/AN2/V
RSRC
RSRC
R/W-0
/4) + ((CVR3:CVR0)/32) • (CV
RSRC
to 0.75 CV
(1)
REF
REF
REF
, with CV
CVRR
R/W-0
Range Selection bit
Preliminary
Source Selection bit
Output Enable bit
W = Writable bit
‘1’ = Bit is set
REF
RSRC
RSRC
Value Selection bits (0 ≤ (CVR3:CVR0) ≤ 15)
, with CV
RSRC
CVRSS
R/W-0
PIC18F45J10 FAMILY
/24 step size (low range)
RSRC
RSRC
used is selected by the CVRR bit (CVRCON<5>). The
primary difference between the ranges is the size of the
steps
(CVR3:CVR0), with one range offering finer resolution.
The equations used to calculate the output of the
comparator voltage reference are as follows:
The comparator reference supply voltage can come
from either V
V
voltage source is selected by the CVRSS bit
(CVRCON<4>).
The settling time of the comparator voltage reference
must be considered when changing the CV
output (see Table 23-3 in Section 23.0 “Electrical
Characteristics”).
)
REF
RSRC
If CVRR = 1:
CV
If CVRR = 0:
CV
CV
= (V
= V
- that are multiplexed with RA2 and RA3. The
(1)
REF
REF
RSRC
selected
DD
/32 step size (high range)
REF
RSRC
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
CVR3
– V
= (CV
= ((CVR3:CVR0)/24) x CV
+) – (V
)
DD
)
SS
REF
and V
RSRC
REF
by
REF
-/CV
R/W-0
-/CV
CVR2
x 1/4) + (((CVR3:CVR0)/32) x
-)
SS
the
REF
, or the external V
REF
pin
CV
pin
x = Bit is unknown
REF
R/W-0
CVR1
DS39682B-page 225
RSRC
Selection
REF
R/W-0
CVR0
+ and
bit 0
REF
bits