PIC18F45J10-I/ML Microchip Technology Inc., PIC18F45J10-I/ML Datasheet - Page 117

• Manufacturer Part Number: PIC18F45J10-I/ML
• Description: 44 PIN, 32 KB FLASH, 1024 RAM
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F45J10-I/ML

• A/d Inputs: 13-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 32
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin QFN
• Programmable Memory: 32K Bytes
• Ram Size: 1K Bytes
• Speed: 40 MHz
• Timers: 1-8 bit, 2-16 bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

11.0
The Timer1 timer/counter module incorporates these
features:
• Software selectable operation as a 16-bit timer or
• Readable and writable 8-bit registers (TMR1H
• Selectable clock source (internal or external) with
• Interrupt-on-overflow
• Reset on CCP Special Event Trigger
• Device clock status flag (T1RUN)
REGISTER 11-1:
© 2006 Microchip Technology Inc.
counter
and TMR1L)
device clock or Timer1 oscillator internal options
TIMER1 MODULE
bit 7
bit 6
bit 5-4
bit 3
bit 2
bit 1
bit 0
T1CON: TIMER1 CONTROL REGISTER
RD16: 16-Bit Read/Write Mode Enable bit
1 = Enables register read/write of TImer1 in one 16-bit operation
0 = Enables register read/write of Timer1 in two 8-bit operations
T1RUN: Timer1 System Clock Status bit
1 = Device clock is derived from Timer1 oscillator
0 = Device clock is derived from another source
T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
T1OSCEN: Timer1 Oscillator Enable bit
1 = Timer1 oscillator is enabled
0 = Timer1 oscillator is shut off
The oscillator inverter and feedback resistor are turned off to eliminate power drain.
T1SYNC: Timer1 External Clock Input Synchronization Select bit
When TMR1CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
When TMR1CS = 0:
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from pin RC0/T1OSO/T1CKI (on the rising edge)
0 = Internal clock (F
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
bit 7
Legend:
R = Readable bit
-n = Value at POR
R/W-0
RD16
T1RUN
R-0
OSC
T1CKPS1
R/W-0
/4)
Preliminary
‘1’ = Bit is set
W = Writable bit
T1CKPS0
R/W-0
PIC18F45J10 FAMILY
A simplified block diagram of the Timer1 module is
shown in Figure 11-1. A block diagram of the module’s
operation in Read/Write mode is shown in Figure 11-2.
The module incorporates its own low-power oscillator
to provide an additional clocking option. The Timer1
oscillator can also be used as a low-power clock source
for the microcontroller in power-managed operation.
Timer1 can also be used to provide Real-Time Clock
(RTC) functionality to applications with only a minimal
addition of external components and code overhead.
Timer1 is controlled through the T1CON Control
register (Register 11-1). It also contains the Timer1
Oscillator Enable bit (T1OSCEN). Timer1 can be
enabled or disabled by setting or clearing control bit,
TMR1ON (T1CON<0>).
T1OSCEN
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
T1SYNC
R/W-0
TMR1CS
x = Bit is unknown
R/W-0
DS39682B-page 115
TMR1ON
R/W-0
bit 0