PIC12F683-E/P Microchip Technology Inc., PIC12F683-E/P Datasheet - Page 26

• Manufacturer Part Number: PIC12F683-E/P
• Description: 8 PIN, 3.5 KB FLASH, 128 RAM, 6 I/O, PDIP
• Manufacturer: Microchip Technology Inc.

Specifications of PIC12F683-E/P

• A/d Inputs: 4 Channel, 10-Bit
• Comparators: 1
• Cpu Speed: 5 MIPS
• Eeprom Memory: 256 Bytes
• Frequency: 20 MHz
• Input Output: 6
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 8-pin PDIP
• Programmable Memory: 3.5K Bytes
• Ram Size: 128 Bytes
• Serial Interface: None
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC12F683
3.4.3
The Low-Frequency Internal Oscillator (LFINTOSC) is
an uncalibrated (approximate) 31 kHz internal clock
source.
The output of the LFINTOSC connects to a postscaler
and multiplexer (see Figure 3-1). 31 kHz can be
selected via software using the IRCF bits (see
Section 3.4.4 “Frequency Select Bits (IRCF)”). The
LFINTOSC is also the frequency for the Power-up
Timer (PWRT), Watchdog Timer (WDT) and Fail-Safe
Clock Monitor (FSCM).
The LFINTOSC is enabled by selecting 31 kHz
(IRCF = 000) as the system clock source (SCS = 1), or
when any of the following are enabled:
• Two-Speed Start-up (IESO = 1 and IRCF = 000)
• Power-up Timer (PWRT)
• Watchdog Timer (WDT)
• Fail-Safe Clock Monitor (FSCM)
The LF Internal Oscillator (LTS) bit (OSCCON<1>)
indicates whether the LFINTOSC is stable or not.
3.4.4
The output of the 8 MHz HFINTOSC and 31 kHz
LFINTOSC connects to a postscaler and multiplexer
(see Figure 3-1). The Internal Oscillator Frequency
select bits, IRCF<2:0> (OSCCON<6:4>), select the
frequency output of the internal oscillators. One of eight
frequencies can be selected via software:
• 8 MHz
• 4 MHz (Default after Reset)
• 2 MHz
• 1 MHz
• 500 kHz
• 250 kHz
• 125 kHz
• 31 kHz
DS41211B-page 24
Note:
LFINTOSC
FREQUENCY SELECT BITS (IRCF)
Following any Reset, the IRCF bits are set
to ‘110’ and the frequency selection is set
to 4 MHz. The user can modify the IRCF
bits to select a different frequency.
Preliminary
3.4.5
When switching between the LFINTOSC and the
HFINTOSC, the new oscillator may already be shut
down to save power. If this is the case, there is a 10 s
delay after the IRCF bits are modified before the fre-
quency selection takes place. The LTS/HTS bits will
reflect the current active status of the LFINTOSC and
the HFINTOSC oscillators. The timing of a frequency
selection is as follows:
1.
2.
3.
4.
5.
6.
If the internal oscillator speed selected is between
8 MHz and 125 kHz, there is no start-up delay before
the new frequency is selected. This is because the old
and the new frequencies are derived from the
HFINTOSC via the postscaler and multiplexer.
3.5
The system clock source can be switched between
external and internal clock sources via software using
the System Clock Select (SCS) bit.
3.5.1
The System Clock Select (SCS) bit (OSCCON<0>)
selects the system clock source that is used for the
CPU and peripherals.
• When SCS = 0, the system clock source is
• When SCS = 1, the system clock source is
determined by configuration of the FOSC<2:0>
bits in the Configuration Word register (CONFIG).
chosen by the internal oscillator frequency
selected by the IRCF bits. After a Reset, SCS is
always cleared.
Note:
IRCF bits are modified.
If the new clock is shut down, a 10 s clock
start-up delay is started.
Clock switch circuitry waits for a falling edge of
the current clock.
CLKOUT is held low and the clock switch
circuitry waits for a rising edge in the new clock.
CLKOUT is now connected with the new clock.
HTS/LTS bits are updated as required.
Clock switch is complete.
Clock Switching
HF AND LF INTOSC CLOCK
SWITCH TIMING
SYSTEM CLOCK SELECT (SCS) BIT
Any automatic clock switch, which may
occur from Two-Speed Start-up or Fail-
Safe Clock Monitor, does not update the
SCS bit. The user can monitor the OSTS
(OSCCON<3>) to determine the current
system clock source.
 2004 Microchip Technology Inc.