DSPIC30F3014-30I/P Microchip Technology Inc., DSPIC30F3014-30I/P Datasheet - Page 133

• Manufacturer Part Number: DSPIC30F3014-30I/P
• Description: DSP, 16-Bit, 24 KB Flash, 2KB RAM, 30 I/O, PDIP-40
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC30F3014-30I/P

• A/d Inputs: 13-Channels, 12-Bit
• Cpu Speed: 30 MIPS
• Eeprom Memory: 1K Bytes
• Input Output: 30
• Interface: CAN, I2C, SPI, UART/USART
• Ios: 30
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 40-pin PDIP
• Programmable Memory: 24K Bytes
• Ram Size: 2K Bytes
• Timers: 3-16-bit, 1-32-bit
• Voltage, Range: 2.5-5.5
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

19.9
The module has two internal power modes.
When the ADON bit is ‘1’, the module is in Active mode;
it is fully powered and functional.
When ADON is ‘0’, the module is in Off mode. The
digital and analog portions of the circuit are disabled for
maximum current savings.
In order to return to the Active mode from Off mode, the
user must wait for the ADC circuitry to stabilize. The
time required to stabilize is specified in the “Electrical
Characteristics”.
19.10 A/D Operation During CPU Sleep
19.10.1
When the device enters Sleep mode, all clock sources
to the module are shut down and stay at logic ‘0’.
If Sleep occurs in the middle of a conversion, the con-
version is aborted. The converter does not continue
with a partially completed conversion on exit from
Sleep mode.
Register contents are not affected by the device
entering or leaving Sleep mode.
The A/D module can operate during Sleep mode if the
A/D clock source is set to RC (ADRC = 1). When the RC
clock source is selected, the A/D module waits one
instruction cycle before starting the conversion. This
allows the SLEEP instruction to be executed which
FIGURE 19-5:
© 2007 Microchip Technology Inc.
RAM Contents:
Read to Bus:
Module Power-down Modes
and Idle Modes
Signed Fractional
A/D OPERATION DURING CPU
SLEEP MODE
Signed Integer
Fractional
Integer
A/D OUTPUT DATA FORMATS
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d11 d11 d11 d11 d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
0
0
0
0
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
eliminates all digital switching noise from the conver-
sion. (When the conversion sequence is complete, the
DONE bit is set.)
If the A/D interrupt is enabled, the device wakes up
from Sleep. If the A/D interrupt is not enabled, the A/D
module is then turned off, although the ADON bit
remains set.
19.10.2
The ADSIDL bit determines if the module stops or con-
tinues on Idle. If ADSIDL = 0, the module continues
operation on assertion of Idle mode. If ADSIDL = 1, the
module stops on Idle.
19.11 Effects of a Reset
A device Reset forces all registers to their Reset state.
This forces the A/D module to be turned off, and any
conversion and sampling sequence is aborted. The val-
ues that are in the ADCBUF registers are not modified.
The A/D Result register contains unknown data after a
Power-on Reset.
19.12 Output Formats
The A/D result is 12 bits wide. The data buffer RAM is
also 12 bits wide. The 12-bit data can be read in one of
four different formats. The FORM<1:0> bits select the
format. Each of the output formats translates to a 16-bit
result on the data bus. Write data is always in right-
justified (integer) format.
dsPIC30F3014/4013
A/D OPERATION DURING CPU IDLE
MODE
0
0
DS70138E-page 131
0
0
0
0
0
0