CY7C924ADX-AXC Cypress Semiconductor Corp, CY7C924ADX-AXC Datasheet - Page 27

• Manufacturer Part Number: CY7C924ADX-AXC
• Description: IC TXRX HOTLINK 100LQFP
• Manufacturer: Cypress Semiconductor Corp
• Series: HOTlink™r
• Type: Transceiverr

Specifications of CY7C924ADX-AXC

• Package / Case: 100-LQFP
• Protocol: Fibre Channel
• Voltage - Supply: 4.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Product: Framer
• Number Of Transceivers: 1
• Data Rate: 622 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Supply Current (max): 250 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage (typ): 5V
• Screening Level: Commercial
• Pin Count: 100
• Mounting: Surface Mount
• Package Type: TQFP
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature (min): 0C
• Operating Temperature (max): 70C
• Ic Interface Type: Parallel, Serial
• Supply Voltage Range: 4.5V To 5.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: TQFP
• No. Of Pins: 100
• No. Of Receivers: 2
• Frequency Max: 50MHz
• Rohs Compliant: Yes
• Termination Type: SMD
• Filter Terminals: SMD
• Driver Case Style: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 428-2918; CY7C924ADX-AXC

Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage temperature ................................ –65 °C to +150 °C
Ambient temperature with
power applied ........................................... –55 °C to +125 °C
Supply voltage to ground potential ...............–0.5 V to +6.5 V
DC voltage applied to outputs
in high-Z State ..................................... –0.5 V to V
CY7C924ADX DC Electrical Characteristics
Document #: 38-02008 Rev. *G
Parameter
V
V
I
I
V
V
I
I
I
I
V
V
V
V
V
I
I
V
V
V
I
I
I
Notes
OST
OZL
IHT
ILT
IHPD
ILPU
IHE
ILE
IHH
ILL
DD
4. Tested one output at a time, output shorted for less than one second, less than 10% duty cycle.
5. The output current and (resulting voltage swing) is set using a single resistor between CURSETx and V
6. To guarantee positive currents for all PECL voltages, an external pull-down resistor must be present.
7. Maximum I
TTL Outputs
TTL Inputs
Transmitter PECL-Compatible Output Pins: OUTA+, OUTA–, OUTB+, OUTB–
Receiver Single-ended PECL-compatible Input Pin: CARDET
Differential Line Receiver Input Pins: INA+, INA–, INB+, INB–
Miscellaneous
OHT
OLT
IHT
ILT
OHE
OLE
ODIF
IHE
ILE
DIFF
IHH
ILL
[6]
[7]
R
outputs unloaded.
CURSET
= (90*Z
Output HIGH Voltage
Output LOW Voltage
Output Short Circuit Current
High-Z Output Leakage Current
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
Input HIGH Current
Input LOW Current
Output HIGH Voltage (V
Output LOW Voltage (V
Output Differential Voltage
|(OUT+) – (OUT–)|
Input HIGH Voltage (V
Input LOW Voltage (V
Input HIGH Current
Input LOW Current
Input Differential Voltage |(IN+) – (IN–)|
Highest Input HIGH Voltage
Lowest Input LOW Voltage
Input HIGH Current
Input LOW Current
Power Supply Current
DD
is measured with V
LOAD
)/V
ODIF
, where Z
Description
DD
= MAX, RFEN = LOW, and outputs unloaded. Typical I
LOAD
DD
DD
DD
DD
referenced)
referenced)
is the differential load between the true and compliment outputs of the differential driver.
referenced)
referenced)
DD
+ 0.5 V
I
I
V
V
V
V
V
Load = 50Ω to V
Load = 50Ω to V
Load = 50Ω to V
10k
V
V
V
V
Freq. = Max.
OH
OL
OUT
IN
IN
IN
IN
IN
IN
IN
IN
= 8 mA, V
= V
= 0.0 V
= V
= 0.0 V, Pins with internal pull-up
= V
= V
= V
= V
= –2 mA, V
= 0 V
Over the Operating Range
DD
DD
IHE
ILE
IHH
ILL
, Pins with internal pull-down
(min.)
(max.)
Min.
Max.
[4]
Test Conditions
Output current into TTL outputs (LOW) ....................... 30 mA
DC input voltage .................................. –0.5 V to V
Static discharge voltage........................................... > 2001 V
(per MIL-STD-883, Method 3015)
Latch-up current ..................................................... > 200 mA
Operating Range
Commercial
Industrial
DD
DD
DD
DD
DD
= Min.
Range
= Min.
– 1.33 V R
– 1.33 V R
DD
– 1.33 V R
is measured with V
[5]
CURSET
CURSET
SS
CURSET
. This CURSET resistor value is calculated as
Ambient Temperature
–40 °C to +85 °C
= 10k V
= 10k
0 °C to +70 °C
DD
=
= 5.0 V, T
V
DD
DD
V
–300
–200
–0.5
Typ.
DD
Min
–30
–20
600
–40
200
170
2.4
2.0
2.5
2.5
– 1.165
– 1.03 V
A
– 2
= 25°C, RFEN = LOW, and
CY7C924ADX
V
V
DD
DD
DD
+300
2500
Max.
1100
Max
–80
V
+40
–40
V
+40
V
750
250
0.4
0.8
5.0 V ± 10%
5.0 V ± 10%
20
– 1.475 V
– 1.62
– 0.83
DD
DD
DD
Page 27 of 62
DD
V
DD
+ 0.5 V
Uni
mA
mV
mV
mA
μA
μA
μA
μA
μA
μA
μA
μA
μA
V
V
V
V
V
V
V
V
V
t