CY7C924ADX-AXC Cypress Semiconductor Corp, CY7C924ADX-AXC Datasheet - Page 26

• Manufacturer Part Number: CY7C924ADX-AXC
• Description: IC TXRX HOTLINK 100LQFP
• Manufacturer: Cypress Semiconductor Corp
• Series: HOTlink™r
• Type: Transceiverr

Specifications of CY7C924ADX-AXC

• Package / Case: 100-LQFP
• Protocol: Fibre Channel
• Voltage - Supply: 4.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Product: Framer
• Number Of Transceivers: 1
• Data Rate: 622 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Supply Current (max): 250 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage (typ): 5V
• Screening Level: Commercial
• Pin Count: 100
• Mounting: Surface Mount
• Package Type: TQFP
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature (min): 0C
• Operating Temperature (max): 70C
• Ic Interface Type: Parallel, Serial
• Supply Voltage Range: 4.5V To 5.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: TQFP
• No. Of Pins: 100
• No. Of Receivers: 2
• Frequency Max: 50MHz
• Rohs Compliant: Yes
• Termination Type: SMD
• Filter Terminals: SMD
• Driver Case Style: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 428-2918; CY7C924ADX-AXC

Document #: 38-02008 Rev. *G
Table 8. Receive Output Bus Signal Map
When a serial address is received and a match is detected, the
address, and all data following that address, is passed to the
Receive FIFO (except in discard policy 3 where the address is
discarded). This continues until a serial address is received
that does not match the contents of the Address Register,
whereupon writes to the Receive FIFO are inhibited.The Serial
Address Register has a power-up default state where the
multicast field set to an all ones condition (FFh or 3FFh). When
set to this value the receiver accepts all data, regardless of the
presence or content of any received serial address. This
“promiscuous” address can also be forced by the momentary
assertion of the RESET*[1:0] pair.
The Serial Address Register is only used when the receiver is
operated with the Receive FIFO enabled (FIFOBYP* is HIGH)
and in operating modes where the discard policy is not 0 (see
Table 7
Serial Address Register Access
The Serial Address Register is accessed through the RXDATA
bus. Both reads and writes to the register require the device to
be addressed (AM* is LOW) and for RXRST* to be asserted
(LOW).
Note
3. First bit shifted in. Others follow in numerical order interpreted from an NRZ pattern.
RXDATA Bus I/O Bit
RXRVS/RXDATA[10]
RXSOC/RXDATA[11]
(FIFOBYP*=HIGH)
RXINT/RXDATA[8]
RXINT/RXDATA[8]
(FIFOBYP*=LOW)
BYTE8/10*
RXDATA[0]
RXDATA[1]
RXDATA[2]
RXDATA[3]
RXDATA[4]
RXDATA[5]
RXDATA[6]
RXDATA[7]
RXDATA[9]
ENCBYP*
on page 24 for a list of discard policies).
RXSC/D*
Character Stream
(8-bit characters)
Decoded 10-bit
RXSC/D*
RXSOC
RXRVS
RXD[0]
RXD[1]
RXD[2]
RXD[3]
RXD[4]
RXD[5]
RXD[6]
RXD[7]
RXINT
(LOW)
HIGH
HIGH
Undecoded 10-bit
Character Stream
RXD[0]
RXD[8]
RXD[8]
RXD[1]
RXD[2]
RXD[3]
RXD[4]
RXD[5]
RXD[6]
RXD[7]
RXD[9]
HIGH
LOW
Receive Decoder Mode
When accessed for write or read operations, the RXRVS
signal is used as a read/write selector, and RXSC/D* is used
to select the operating mode (multicast or unicast) of the Serial
Address Register.
Figure 6. Serial Address Register Format and Access
[3]
RXDATA[9] or [7]
MSB
0
0
0
0
0
0
0
0
Address Register Content
(10-bit characters)
Character Stream
0
0
1
1
Decoded 10-bit
Serial Address Register
Byte-Packed
0
1
0
1
RXSC/D*
RXSOC
RXRVS
RXD[0]
RXD[1]
RXD[2]
RXD[3]
RXD[4]
RXD[5]
RXD[6]
RXD[7]
RXD[8]
RXD[8]
RXD[9]
HIGH
LOW
[3]
Multicast Address write
Multicast Address read
Unicast Address read
Unicast Address write
Undecoded 12-bit
Character Stream
CY7C924ADX
RXDATA[0]
RXD[0]
RXD[10]
RXD[11]
RXD[1]
RXD[2]
RXD[3]
RXD[4]
RXD[5]
RXD[6]
RXD[7]
RXD[8]
RXD[8]
RXD[9]
LSB
LOW
LOW
Page 26 of 62
[3]