ISP1362EE ST-Ericsson Inc, ISP1362EE Datasheet - Page 63
![no-image](/images/manufacturer_photos/0/6/627/st-ericsson_inc_sml.jpg)
ISP1362EE
Manufacturer Part Number
ISP1362EE
Description
IC USB CTRL SNGL CHIP 64TFBGA
Manufacturer
ST-Ericsson Inc
Datasheet
1.ISP1362EEUM.pdf
(153 pages)
Specifications of ISP1362EE
Controller Type
USB 2.0 Controller
Interface
Parallel/Serial
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-TFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Supply
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1362EE/01
Manufacturer:
KAWASAKI
Quantity:
1 200
Part Number:
ISP1362EE/01
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Company:
Part Number:
ISP1362EEUM
Manufacturer:
IDT
Quantity:
300
NXP Semiconductors
Table 24.
ISP1362_5
Product data sheet
Bit
Symbol
Reset
Access
Bit
Symbol
Reset
Access
OtgStatus register: bit allocation
13.2 OtgStatus register (R: 67h)
15
7
-
-
-
-
reserved
Table 23.
Code (Hex): 67 — read only
Table 25.
Bit
2
1
0
Bit
15 to 10
9
8 to 6
5
4
14
6
-
-
-
-
Symbol
DISCHRG_
VBUS
CHRG_VBUS This bit is for the B-device only. If set, it will charge V
DRV_VBUS
OtgControl register: bit description
OtgStatus register: bit description
Symbol
-
SE0_2MS
-
RMT_CONN
B_SESS_VLD
CONN
RMT_
13
R
5
0
-
-
reserved
Description
This bit is for the B-device only. If set, it will enable a pull-down resistor
on V
end threshold voltage.
0 — disable
1 — enable
resistor.
0 — disable charging V
1 — enable charging V
This bit is used to enable the on-chip charge pump or external power
source to drive V
time.
0 — disable driving V
1 — enable driving V
Rev. 05 — 8 May 2007
BUS
B_SESS_
Description
reserved
0 — bus is in SE0 for less than 2 ms
1 — bus is in SE0 for more than 2 ms
reserved
0 — remote pull-up resistor disconnected
1 — remote pull-up resistor connected
Remark: When the local pull-up resistor on the DP line is disabled,
a 50 s delay is applied before the RMT_CONN detection is
enabled.
For the B-device (ID_REG = 1), this bit is a B-device session valid
indicator (B_SESS_VLD).
0 — V
1 — V
, which will help to speed up discharging of V
VLD
12
R
4
0
-
-
BUS
BUS
is lower than VB_SESS_VLD
is higher than VB_SESS_VLD
BUS
A_SESS_
. For the B-device, it shall not enable this bit at any
BUS
BUS
VLD
11
BUS
BUS
R
3
0
-
-
…continued
of the OTG port
of the OTG port
of the OTG port
of the OTG port
B_SESS_
Single-chip USB OTG Controller
END
10
R
2
1
-
-
SE0_2MS
A_VBUS_
VLD
R
R
9
0
1
0
© NXP B.V. 2007. All rights reserved.
BUS
BUS
ISP1362
through a
below session
reserved
ID_REG
62 of 152
R
8
0
1
-
-