MCP2515-I/SO Microchip Technology, MCP2515-I/SO Datasheet - Page 54

• Manufacturer Part Number: MCP2515-I/SO
• Description: IC CAN CONTROLLER W/SPI 18SOIC
• Manufacturer: Microchip Technology

Specifications of MCP2515-I/SO

• Package / Case: 18-SOIC (7.5mm Width)
• Controller Type: CAN Interface
• Interface: SPI
• Voltage - Supply: 2.7 V ~ 5.5 V
• Current - Supply: 10mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 1 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Supply Current (max): 10 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Voltage Range: 2.7V To 5.5V
• Driver Case Style: SOIC
• No. Of Pins: 18
• Operating Temperature Range: -40°C To +85°C
• Filter Terminals: SMD
• Supply Voltage Min: 2.7V
• Rohs Compliant: Yes
• Clock Frequency: 40MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP2515DM-BM - BOARD DEMO FOR MCP2515/51MCP2515DM-PTPLS - BOARD DAUGHTER PICTAIL MCP2515MCP2515DM-PCTL - BOARD DEMO FOR MCP2515DV251001 - KIT DEVELOPMENT CAN MCP2510
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MCP2515
FIGURE 8-3:
TABLE 8-1:
DS21801F-page 54
Capacitor values are for design guidance only:
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values are not optimized.
Different capacitor values may be required to
produce acceptable oscillator operation. The user
should test the performance of the oscillator over the
expected V
application.
See the notes following
information.
Mode
HS
Typical Capacitor Values Used:
DD
16.0 MHz
8.0 MHz
and temperature range for the
Freq.
Resonators Used:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
74AS04
330 kΩ
16.0 MHz
EXTERNAL SERIES RESONANT CRYSTAL OSCILLATOR CIRCUIT
4.0 MHz
8.0 MHz
Note 1: Duty cycle restrictions must be observed (see
Table 8-2
OSC1
27 pF
22 pF
for additional
0.1 mF
XTAL
OSC2
27 pF
22 pF
74AS04
330 kΩ
TABLE 8-2:
Capacitor values are for design guidance only:
These capacitors were tested with the crystals listed
below for basic start-up and operation. These values
are not optimized.
Different capacitor values may be required to
produce acceptable oscillator operation. The user
should test the performance of the oscillator over the
expected V
application.
See the notes following this Table for additional
information.
Note 1:
Type
74AS04
Osc
HS
2:
3:
4:
(1)(4)
While higher capacitance increases the
stability of the oscillator, it also increases
the start-up time.
Since each resonator/crystal has its own
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate values of external
components.
R
crystals with low drive level specification.
Always verify oscillator performance over
the V
expected for the application.
DD
S
To Other
Devices
may be required to avoid overdriving
and temperature range for the
Table
DD
20 MHz
Crystal
Freq.
4 MHz
8 MHz
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
Crystals Used
and temperature range that is
20.0 MHz
(2)
12-1).
4.0 MHz
8.0 MHz
© 2010 Microchip Technology Inc.
MCP2510
OSC1
Typical Capacitor
27 pF
22 pF
15 pF
(3)
C1
Values Tested:
(1)
:
27 pF
22 pF
15 pF
C2