MCP2515-I/SO Microchip Technology, MCP2515-I/SO Datasheet - Page 25

• Manufacturer Part Number: MCP2515-I/SO
• Description: IC CAN CONTROLLER W/SPI 18SOIC
• Manufacturer: Microchip Technology

Specifications of MCP2515-I/SO

• Package / Case: 18-SOIC (7.5mm Width)
• Controller Type: CAN Interface
• Interface: SPI
• Voltage - Supply: 2.7 V ~ 5.5 V
• Current - Supply: 10mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 1 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Supply Current (max): 10 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Voltage Range: 2.7V To 5.5V
• Driver Case Style: SOIC
• No. Of Pins: 18
• Operating Temperature Range: -40°C To +85°C
• Filter Terminals: SMD
• Supply Voltage Min: 2.7V
• Rohs Compliant: Yes
• Clock Frequency: 40MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP2515DM-BM - BOARD DEMO FOR MCP2515/51MCP2515DM-PTPLS - BOARD DAUGHTER PICTAIL MCP2515MCP2515DM-PCTL - BOARD DEMO FOR MCP2515DV251001 - KIT DEVELOPMENT CAN MCP2510
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.4.3
When used as digital outputs, the BFPCTRL.BxBFM bit
must be cleared and BFPCTRL.BnBFE must be set for
the associated buffer. In this mode, the state of the pin
is controlled by the BFPCTRL.BnBFS bits. Writing a ‘1’
to the BnBFS bit will cause a high level to be driven on
the associated buffer full pin, while a ‘0’ will cause the
pin to drive low. When using the pins in this mode, the
state of the pin should be modified only by using the Bit
Modify SPI command to prevent glitches from
occurring on either of the buffer full pins.
FIGURE 4-2:
© 2010 Microchip Technology Inc.
Note:
CONFIGURED AS DIGITAL OUTPUT
Messages received in the MAB are intially
applied to the mask and filters of RXB0. In
addition, only one filter match occurs (e.g.,
if the message matches both RXF0 and
RXF2, the match will be for RXF0 and the
message will be moved into RXB0).
RECEIVE BUFFER BLOCK DIAGRAM
A
c
c
e
p
t
R
X
B
0
Acceptance Mask
Acceptance Filter
Acceptance Filter
Identifier
Data Field
RXM0
RXF0
RXF1
TABLE 4-1:
BnBFE BnBFM BnBFS
0
1
1
1
M
A
B
Acceptance Mask
X
1
0
0
Acceptance Filter
Acceptance Filter
Acceptance Filter
Acceptance Filter
Data Field
Identifier
CONFIGURING RXNBF PINS
RXM1
RXF2
RXF3
RXF4
RXF5
X
X
0
1
Disabled, high-impedance
Receive buffer interrupt
Digital output = 0
Digital output = 1
MCP2515
Pin Status
DS21801F-page 25
R
X
B
1
A
c
c
e
p
t