EP2C5F256C8 Altera, EP2C5F256C8 Datasheet - Page 84

IC CYCLONE II FPGA 5K 256-FBGA

EP2C5F256C8

Manufacturer Part Number
EP2C5F256C8
Description
IC CYCLONE II FPGA 5K 256-FBGA
Manufacturer
Altera
Series
Cyclone® IIr
Datasheet

Specifications of EP2C5F256C8

Number Of Logic Elements/cells
4608
Number Of Labs/clbs
288
Total Ram Bits
119808
Number Of I /o
158
Voltage - Supply
1.15 V ~ 1.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
256-FBGA
Family Name
Cyclone® II
Number Of Logic Blocks/elements
4608
# I/os (max)
158
Frequency (max)
402.58MHz
Process Technology
90nm
Operating Supply Voltage (typ)
1.2V
Logic Cells
4608
Ram Bits
119808
Operating Supply Voltage (min)
1.15V
Operating Supply Voltage (max)
1.25V
Operating Temp Range
0C to 85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
256
Package Type
FBGA
No. Of Macrocells
4608
Family Type
Cyclone II
No. Of I/o's
158
Clock Management
PLL
I/o Supply Voltage
3.6V
Operating Frequency Max
320MHz
Rohs Compliant
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Lead Free Status / Rohs Status
Not Compliant
Other names
544-1446

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EP2C5F256C8
Manufacturer:
TOSHIBA
Quantity:
1
Part Number:
EP2C5F256C8
Manufacturer:
Altera
Quantity:
10 000
Part Number:
EP2C5F256C8
Manufacturer:
ALTERA
0
Part Number:
EP2C5F256C8
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Part Number:
EP2C5F256C8N
Manufacturer:
ALTBRA
Quantity:
36
Part Number:
EP2C5F256C8N
Manufacturer:
ALTERA82
Quantity:
1 080
Part Number:
EP2C5F256C8N
Manufacturer:
Altera
Quantity:
10 000
Part Number:
EP2C5F256C8N
Manufacturer:
ALTERA/PBF
Quantity:
5
Part Number:
EP2C5F256C8N
Manufacturer:
ALTERA
0
Part Number:
EP2C5F256C8N
Manufacturer:
ALTERA
Quantity:
21
Part Number:
EP2C5F256C8N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Part Number:
EP2C5F256C8N
Manufacturer:
ALTEAR
Quantity:
14 530
Part Number:
EP2C5F256C8N
Manufacturer:
ALTERA82
Quantity:
6 798
Part Number:
EP2C5F256C8N
0
Cyclone II Hot-Socketing Specifications
4–2
Cyclone II Device Handbook, Volume 1
Devices Can Be Driven before Power-Up
You can drive signals into the I/O pins, dedicated input pins, and
dedicated clock pins of Cyclone II devices before or during power-up or
power-down without damaging the device. Cyclone II devices support
any power-up or power-down sequence (V
system level design.
I/O Pins Remain Tri-Stated during Power-Up
A device that does not support hot socketing may interrupt system
operation or cause contention by driving out before or during power-up.
In a hot-socketing situation, the Cyclone II device’s output buffers are
turned off during system power-up or power-down. The Cyclone II
device also does not drive out until the device is configured and has
attained proper operating conditions. The I/O pins are tri-stated until the
device enters user mode with a weak pull-up resistor (R) to 3.3V. Refer to
Figure 4–1
1
This specification takes into account the pin capacitance but not board
trace and external loading capacitance. You must consider additional
capacitance for trace, connector, and loading separately.
I
specification applies when all V
powered-up or powered-down conditions. For the AC specification, the
peak current duration due to power-up transients is 10 ns or less.
A possible concern for semiconductor devices in general regarding hot
socketing is the potential for latch-up. Latch-up can occur when electrical
subsystems are hot socketed into an active system. During hot socketing,
the signal pins may be connected and driven by the active system before
IOPIN
The hot-socketing DC specification is | I
The hot-socketing AC specification is | I
less.
is the current at any user I/O pin on the device. The DC
You can power up or power down the V
any sequence. The V
to their steady state levels. (Refer to
information.) The power supply ramp rates can range from
100 µs to 100 ms for non “A” devices. Both V
power down within 100 ms of each other to prevent I/O pins
from driving out. During hot socketing, the I/O pin capacitance
is less than 15 pF and the clock pin capacitance is less than 20 pF.
Cyclone II devices meet the following hot-socketing
specification.
for more information.
CCIO
CC
and V
supplies to the device are stable in the
CCINT
CCIO
IOPIN
IOPIN
Figure 4–3
must have monotonic rise
and V
CCIO
| < 300 µA.
| < 8 mA for 10 ns or
and V
CCINT
CC
Altera Corporation
for more
supplies must
February 2007
) to simplify
CCINT
pins in

Related parts for EP2C5F256C8