DSP56301PW80 Freescale Semiconductor, DSP56301PW80 Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/2/262/freescale_semiconductor_sml.jpg)
DSP56301PW80
Manufacturer Part Number
DSP56301PW80
Description
IC DSP 24BIT 80MHZ 208-LQFP
Manufacturer
Freescale Semiconductor
Series
DSP563xxr
Type
Fixed Pointr
Datasheet
1.DSP56301VF100.pdf
(124 pages)
Specifications of DSP56301PW80
Interface
Host Interface, SSI, SCI
Clock Rate
80MHz
Non-volatile Memory
ROM (9 kB)
On-chip Ram
24kB
Voltage - I/o
3.30V
Voltage - Core
3.30V
Operating Temperature
-40°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
208-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSP56301PW80
Manufacturer:
SLA
Quantity:
6 217
Company:
Part Number:
DSP56301PW80
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Freescale Semiconductor
Notes:
No.
28
29
DMA Request Rate
•
•
•
•
Delay from IRQA, IRQB, IRQC, IRQD, NMI assertion to
external memory (DMA source) access address out valid
Data read from HI32, ESSI, SCI
Data write to HI32, ESSI, SCI
Timer
IRQ, NMI (edge trigger)
1.
2.
3.
4.
5.
6.
7.
8.
When using fast interrupts and IRQA, IRQB, IRQC, and IRQD are defined as level-sensitive, timings 19 through 21 apply to
prevent multiple interrupt service. To avoid these timing restrictions, the deasserted Edge-triggered mode is recommended
when using fast interrupts. Long interrupts are recommended when using Level-sensitive mode.
This timing depends on several settings:
• For PLL disable, using internal oscillator (PLL Control Register (PCTL) Bit 16 = 0) and oscillator disabled during Stop (PCTL
Bit 17 = 0), a stabilization delay is required to assure that the oscillator is stable before programs are executed. Resetting the
Stop delay (Operating Mode Register Bit 6 = 0) provides the proper delay. While Operating Mode Register Bit 6 = 1 can be set,
it is not recommended, and these specifications do not guarantee timings for that case.
• For PLL disable, using internal oscillator (PCTL Bit 16 = 0) and oscillator enabled during Stop (PCTL Bit 17=1), no
stabilization delay is required and recovery is minimal (Operating Mode Register Bit 6 setting is ignored).
• For PLL disable, using external clock (PCTL Bit 16 = 1), no stabilization delay is required and recovery time is defined by the
PCTL Bit 17 and Operating Mode Register Bit 6 settings.
• For PLL enable, if PCTL Bit 17 is 0, the PLL is shutdown during Stop. Recovering from Stop requires the PLL to get locked.
The PLL lock procedure duration, PLL Lock Cycles (PLC), may be in the range of 0 to 1000 cycles. This procedure occurs in
parallel with the stop delay counter, and stop recovery ends when the last of these two events occurs. The stop delay counter
completes count or PLL lock procedure completion.
• PLC value for PLL disable is 0.
• The maximum value for ET
4096/66 MHz = 62 μs). During the stabilization period, T
vary as well.
Periodically sampled and not 100 percent tested.
Value depends on clock source:
• For an external clock generator, RESET duration is measured while RESET is asserted, V
active and valid.
• For an internal oscillator, RESET duration is measured while RESET is asserted and V
reflects the crystal oscillator stabilization time after power-up. This number is affected both by the specifications of the crystal
and other components connected to the oscillator and reflects worst case conditions.
• When the V
device circuitry is in an uninitialized state that can result in significant power consumption and heat-up. Designs should
minimize this state to the shortest possible duration.
If PLL does not lose lock.
V
WS = number of wait states (measured in clock cycles, number of T
Use the expression to compute a maximum value.
CC
= 3.3 V ± 0.3 V; T
Table 2-7.
Characteristics
A[0–23]
RESET
All Pins
CC
is valid, but the other “required RESET duration” conditions (as specified above) have not been yet met, the
J
= –40°C to +100°C, C
Reset, Stop, Mode Select, and Interrupt Timing
C
8
is 4096 (maximum MF) divided by the desired internal frequency (that is, for 66 MHz it is
DSP56301 Technical Data, Rev. 10
Figure 2-3.
L
= 50 pF.
Reset Value
Reset Timing
C
, T
9
4.25 × T
Expression
H,
6 × T
7 × T
2 × T
3 × T
and T
C
C
C
C
C
+ 2.0
C
L
).
is not constant, and their width may vary, so timing may
Min
55.1
—
—
—
—
6
80 MHz
(Continued)
CC
CC
is valid. The specified timing
AC Electrical Characteristics
Max
10
75.0
87.5
25.0
37.5
is valid, and the EXTAL input is
—
First Fetch
Min
44.5
—
—
—
—
V
100 MHz
IH
Max
60.0
70.0
20.0
30.0
—
Unit
ns
ns
ns
ns
ns
2-9