PIC16F1526T-I/PT Microchip Technology, PIC16F1526T-I/PT Datasheet - Page 286

• Manufacturer Part Number: PIC16F1526T-I/PT
• Description: 64-pin, 14KB Flash, 768B RAM, 10-bit ADC, 10xCCP, 2xSPI, 2xMI2C, 2xEUSART, 2.3V-
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1526T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 5.5 V
• Data Converters: A/D 30x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16(L)F1526/27
23.2
The Low-Voltage Programming Entry mode allows the
PIC16(L)F1526/27 devices to be programmed using
V
Configuration Word 2 is set to ‘1’, the low-voltage ICSP
programming entry is enabled. To disable the
Low-Voltage ICSP mode, the LVP bit must be
programmed to ‘0’.
Entry into the Low-Voltage Programming Entry mode
requires the following steps:
1.
2.
Once the key sequence is complete, MCLR must be
held at V
maintained.
If low-voltage programming is enabled (LVP = 1), the
MCLR Reset function is automatically enabled and
cannot be disabled. See
Brown-out Reset (LPBOR)”
The LVP bit can only be reprogrammed to ‘0’ by using
the High-Voltage Programming mode.
23.3
Connection to a target device is typically done through
an ICSP™ header. A commonly found connector on
development tools is the RJ-11 in the 6P6C (6 pin, 6
connector) configuration. See
FIGURE 23-3:
DS41458B-page 286
DD
MCLR is brought to V
A 32-bit key sequence is presented on
ICSPDAT, while clocking ICSPCLK.
only, without high voltage. When the LVP bit of
IL
Low-Voltage Programming Entry
Mode
Common Programming Interfaces
for as long as Program/Verify mode is to be
*
PICkit™ STYLE CONNECTOR INTERFACE
The 6-pin header (0.100" spacing) accepts 0.025" square pins.
IL
.
Section 6.3 “Low-Power
for more information.
Figure
23-2.
Preliminary
Pin 1 Indicator
1
2
3
4
5
6
FIGURE 23-2:
Another connector often found in use with the PICkit™
programmers is a standard 6-pin header with 0.1 inch
spacing. Refer to
V
PP
V
DD
/MCLR
Pin Description*
1 = V
2 = V
3 = V
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
Pin Description*
1 = V
2 = V
3 = V
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
PP
DD
SS
/MCLR
1
Target
(ground)
PP
DD
SS
Figure
2
3
/MCLR
4
(ground)
Target
5
V
6
SS
ICSPDAT
ICD RJ-11 STYLE
CONNECTOR INTERFACE
 2011 Microchip Technology Inc.
23-3.
ICSPCLK
NC
Target
PC Board
Bottom Side