LAN9311I-NZW Standard Microsystem (Smsc), LAN9311I-NZW Datasheet - Page 228
![no-image](/images/no-image-200.jpg)
LAN9311I-NZW
Manufacturer Part Number
LAN9311I-NZW
Description
Manufacturer
Standard Microsystem (Smsc)
Datasheet
1.LAN9311-NU.pdf
(460 pages)
Specifications of LAN9311I-NZW
Package
128XVTQFP
Phy/transceiver Interface
MII
Number Of Primary Switch Ports
2
Maximum Data Rate
100 Mbps
Internal Memory Buffer Size
32 KB
Vlan Support
Yes
Power Supply Type
Analog
Minimum Single Supply Voltage
3 V
Maximum Single Supply Voltage
3.6 V
Maximum Supply Current
0.295 A
Maximum Power Dissipation
1070 mW
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LAN9311I-NZW
Manufacturer:
Standard
Quantity:
836
Company:
Part Number:
LAN9311I-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
- Current page: 228 of 460
- Download datasheet (5Mb)
Revision 1.7 (06-29-10)
BITS
3
2
1
0
1588 Port 0(Host MAC) TX Interrupt (1588_MII_TX_INT)
This interrupt indicates that a packet from the Host MAC to the switch fabric
matches the configured PTP packet and the 1588 clock was captured.
Note:
1588 GPIO9 Interrupt (1588_GPIO9_INT)
This interrupt indicates that an event on GPIO9 occurred and the 1588 clock
was captured. These interrupts are configured through the
I/O Configuration Register (GPIO_CFG)
Note:
1588 GPIO8 Interrupt (1588_GPIO8_INT)
This interrupt indicates that an event on GPIO8 occurred and the 1588 clock
was captured. These interrupts are configured through the
I/O Configuration Register (GPIO_CFG)
Note:
1588 Timer Interrupt (1588_TIMER_INT)
This interrupt indicates that the 1588 clock equaled or passed the Clock
Target value in the
(1588_CLOCK_TARGET_HI)
(1588_CLOCK_TARGET_LO).
Note:
For Port 0, receive is defined as data from the switch fabric, while
transmit is to the switch fabric.
As 1588 capture inputs, GPIO inputs are edge sensitive and must
be active for greater than 40 nS to be recognized as interrupt
inputs.
As 1588 capture inputs, GPIO inputs are edge sensitive and must
be active for greater than 40 nS to be recognized as interrupt
inputs.
This bit is also cleared by an active edge on GPIO[9:8] if enabled.
For the clear function, GPIO inputs are edge sensitive and must be
active for greater than 40 nS to be recognized as a clear input.
Refer to
additional information.
Section 13.2, "GPIO Operation," on page 163
1588 Clock Target High-DWORD Register
and
DESCRIPTION
1588 Clock Target Low-DWORD Register
DATASHEET
register.
register.
228
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
General Purpose
General Purpose
for
TYPE
R/WC
R/WC
R/WC
R/WC
SMSC LAN9311/LAN9311i
DEFAULT
Datasheet
0b
0b
0b
0b
Related parts for LAN9311I-NZW
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN9311-NZW](/images/no-image3.png)
Part Number:
Description:
Ethernet Switch 2-Port 10Mbps/100Mbps 128-Pin XVTQFP
Manufacturer:
Standard Microsystem (Smsc)
Datasheet:
![LAN9303-ABZJ](/images/no-image3.png)
Part Number:
Description:
Ethernet Switch 3-Port 10Mbps/100Mbps 56-Pin QFN EP
Manufacturer:
Standard Microsystem (Smsc)
Datasheet: