LAN9303-ABZJ Standard Microsystem (Smsc), LAN9303-ABZJ Datasheet - Page 96
![no-image](/images/no-image-200.jpg)
LAN9303-ABZJ
Manufacturer Part Number
LAN9303-ABZJ
Description
Ethernet Switch 3-Port 10Mbps/100Mbps 56-Pin QFN EP
Manufacturer
Standard Microsystem (Smsc)
Datasheet
1.LAN9303-ABZJ.pdf
(367 pages)
Specifications of LAN9303-ABZJ
Package
56QFN EP
Phy/transceiver Interface
MII/RMII
Number Of Primary Switch Ports
3
Maximum Data Rate
100 Mbps
Vlan Support
Yes
Power Supply Type
Analog
Minimum Single Supply Voltage
3 V
Maximum Single Supply Voltage
3.6 V
Maximum Supply Current
0.19(Typ) A
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LAN9303-ABZJ
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
- Current page: 96 of 367
- Download datasheet (4Mb)
Revision 1.4 (07-07-10)
7.2.4.3
7.2.4.4
7.2.5
Register
Manchester signal and generates the received 20MHz clock from it. Using this clock, the Manchester
encoded data is extracted and converted to a 10MHz NRZI data stream. It is then converted from serial
to 4-bit wide parallel data.
The RX10M block also detects valid 10BASE-T IDLE signals - Normal Link Pulses (NLPs) - to maintain
the link.
MII MAC Interface
For reception, the 4-bit data nibbles are sent to the MII MAC Interface block where they are sent via
MII to the Switch Fabric MAC. The MII MAC Interface is described in detail in
Interface".
Note: The PHY is connected to the Switch Fabric MAC via standard MII signals. Refer to the IEEE
Jabber Detection
Jabber is a condition in which a station transmits for a period of time longer than the maximum
permissible packet length, usually due to a fault condition, that results in holding the TXEN input for
an extended period of time. Special logic is used to detect the jabber state and abort the transmission
to the line, within 45ms. Once TXEN is deasserted, the logic resets the jabber condition.
PHY Auto-negotiation
The purpose of the auto-negotiation function is to automatically configure the PHY to the optimum link
parameters based on the capabilities of its link partner. Auto-negotiation is a mechanism for
exchanging configuration information between two link-partners and automatically selecting the highest
performance mode of operation supported by both sides. Auto-negotiation is fully defined in clause 28
of the IEEE 802.3 specification and is enabled by setting the
Port x PHY Basic Control Register
The advertised capabilities of the PHY are stored in the
Register
both full or half-duplex modes. Besides the connection speed, the PHY can advertise remote fault
indication and symmetric or asymmetric pause flow control as defined in the IEEE 802.3 specification.
“Next Page” capability is not supported. Many of the default advertised capabilities of the PHY are
determined via configuration straps as shown in
Advertisement Register (PHY_AN_ADV_x)," on page
Straps," on page 45
Once auto-negotiation has completed, information about the resolved link and the results of the
negotiation process are reflected in the speed indication bits in the
Register
Partner Base Page Ability Register
The auto-negotiation protocol is a purely physical layer activity and proceeds independently of the MAC
controller.
The following blocks are activated during an Auto-negotiation session:
Auto-negotiation (digital)
100M ADC (analog)
100M PLL (analog)
100M equalizer/BLW/clock recovery (DSP)
10M SQUELCH (analog)
10M PLL (analog)
10M TX Driver (analog)
802.3 specification for additional details.
(PHY_AN_ADV_x). The PHY contains the ability to advertise 100BASE-TX and 10BASE-T in
(PHY_SPECIAL_CONTROL_STATUS_x), as well as the
(PHY_SPECIAL_CONTROL_STAT_IND_x). The 10M PLL locks onto the received
for additional details on the configuration straps.
Small Form Factor Three Port 10/100 Managed Ethernet Switch with Single MII/RMII/Turbo MII
DATASHEET
(PHY_BASIC_CONTROL_x).
(PHY_AN_LP_BASE_ABILITY_x).
96
Section 13.3.2.5, "Port x PHY Auto-Negotiation
199. Refer to
Port x PHY Auto-Negotiation Advertisement
Auto-Negotiation (PHY_AN)
Port x PHY Auto-Negotiation Link
Port x PHY Special Control/Status
Section 4.2.4, "Configuration
Section 7.2.7, "MII MAC
SMSC LAN9303/LAN9303i
Datasheet
bit of the
Related parts for LAN9303-ABZJ
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN9311-NZW](/images/no-image3.png)
Part Number:
Description:
Ethernet Switch 2-Port 10Mbps/100Mbps 128-Pin XVTQFP
Manufacturer:
Standard Microsystem (Smsc)
Datasheet:
![LAN9311I-NZW](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Standard Microsystem (Smsc)
Datasheet: