CP3BT10G38 National Semiconductor, CP3BT10G38 Datasheet - Page 93

• Manufacturer Part Number: CP3BT10G38
• Description: IC CPU RISC W/LLC&USB 100-LQFP
• Manufacturer: National Semiconductor

Specifications of CP3BT10G38

• Applications: Connectivity Processor
• Core Processor: CR16C
• Program Memory Type: FLASH (256 kB)
• Controller Series: CP3000
• Ram Size: 10K x 8
• Interface: Bluetooth, ACCESS.bus, Audio, UART, USB, Microwire/SPI
• Number Of I /o: 37
• Voltage - Supply: 2.25 V ~ 2.75 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *CP3BT10G38

16.3.36 Receive Command Register n (RXCn)
Each of the receive endpoints (2, 4, and 6) has one RXCn
register. The registers provide read/write access from the
CPU bus. Reading reserved bits returns undefined data. Af-
ter reset, it is clear.
RX_EN
IGN_SETUP The Ignore SETUP Tokens bit controls wheth-
FLUSH
RFWL
Res. RFWL Res. FLUSH IGN_SETUP Res. RX_EN
7
6
5
The Receive Enable bit enables receiving
packets. OUT packet reception is disabled af-
ter every data packet is received, or when a
STALL handshake is returned in response to
an OUT token. The RX_EN bit must be set to
re-enable data reception. Reception of SET-
UP packets is always enabled. In the case of
back-to-back SETUP packets (for a given
endpoint) where a valid SETUP packet is re-
ceived with no other intervening non-SETUP
tokens, the Endpoint Controller discards the
new SETUP packet and returns an ACK hand-
shake. If any other reasons prevent the End-
point Controller from accepting the SETUP
packet, it must not generate a handshake.
0 – Receive disabled.
1 – Receive enabled.
er SETUP tokens are ignored. When this bit is
set, the endpoint ignores any SETUP tokens
directed to its configured address.
0 – Do not ignore SETUP tokens.
1 – Ignore SETUP tokens.
Writing 1 to the Flush bit flushes all data from
the corresponding receive FIFO, resets the
endpoint to Idle state, and clears the FIFO
read and write pointers. If the endpoint is cur-
rently using FIFO to receive data, flushing is
delayed until after the transfer is complete.
0 – Writing 0 has no effect.
1 – Writing 1 flushes the FIFOs.
The Receive FIFO Warning Limit field speci-
fies how many more bytes can be received to
the respective FIFO before an overrun condi-
tion occurs. If the number of empty bytes re-
maining in the FIFO is equal to or less than
the selected warning limit, the RXWARN bit in
the FWEV register is set.
Table 41 Receive FIFO Warning Limit
RFWL
4
00
01
10
11
3
Bytes Remaining in FIFO
RFWL disabled
2
≤ 16
≤ 4
≤ 8
1
0
93
16.3.37 Receive Data Register n (RXD)
Each of the three Receive Endpoint FIFOs has one RXD
register. Reading the Receive Data register n returns the
data located in the receive FIFO n at the current position of
the receive read pointer. These registers provide read-only
access from the CPU bus.
RXFD
16.4
Separate UVCC and UGND pins are provided for the USB
transceiver, so it can be powered at the standard USB volt-
age of 3.3V while the other parts of the device run at other
voltages. The USB transceiver is powered by the system,
not the USB cable, so these pins must be connected to a
power supply and the system ground.
The on-chip USB transceiver does not have enough imped-
ance to meet the USB specification requirement, so exter-
nal 22-ohm resistors are required in series with the D+ and
D- pins, as shown in Figure 29.
7
Figure 29. USB Transceiver Interface
TRANSCEIVER INTERFACE
The Receive FIFO Data Byte is used to read
the receive FIFO. Software should expect to
read only the packet payload data. The PID
and CRC16 are terminated by the receive
state machine.
CP3BT10
UGND
UVCC
D+
D-
RXFD
+3.3V
22
22
www.national.com
DS123
USB
Cable
0