ADUC7060BSTZ32 Analog Devices Inc, ADUC7060BSTZ32 Datasheet - Page 66

• Manufacturer Part Number: ADUC7060BSTZ32
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7060BSTZ32

• Design Resources: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Cpu Family: ADuC7xxx
• Device Core: ARM7TDMI
• Device Core Size: 16/32Bit
• Frequency (max): 10.24MHz
• Interface Type: I2C/SPI/UART
• Total Internal Ram Size: 4KB
• # I/os (max): 14
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 2.625V
• Operating Supply Voltage (min): 2.375V
• On-chip Adc: 2(4-chx24-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: ADuC7xxx
• Maximum Speed: 10.24 MHz
• Operating Supply Voltage: 2.5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 14
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

ADuC7060/ADuC7061
TIMER0
Timer0 is a 32-bit, general-purpose timer, count down or count
up, with a programmable prescaler. The prescaler source can be
the low power 32.768 kHz oscillator, the core clock, or from one
of two external GPIOs. This source can be scaled by a factor of
1, 16, 256, or 32,768. This gives a minimum resolution of 97.66 ns
with a prescaler of 1 (ignoring the external GPIOs).
The counter can be formatted as a standard 32-bit value or as
hours:minutes:seconds:hundredths.
Timer0 has a capture register (T0CAP) that is triggered by a
selected IRQ source initial assertion. When triggered, the current
timer value is copied to T0CAP, and the timer continues to run.
Use this feature to determine the assertion of an event with
increased accuracy. Note that only peripherals that have their
IRQ source enabled can be used with the timer capture feature.
The Timer0 interface consists of five MMRS: T0LD, T0VAL,
T0CAP, T0CLRI, and T0CON.
•
•
•
Timer0 features a postscaler that allows the user to count between
1 and 256 the number of Timer0 timeouts. To activate the post-
scaler, the user sets Bit 18 and writes the desired number to count
into Bits[24:31] of T0CON. When that number of timeouts is
reached, Timer0 can generate an interrupt if T0CON[18] is set.
Note that, if the part is in a low power mode and Timer0 is
clocked from the GPIO or low power oscillator source, Timer0
continues to operate.
Timer0 reloads the value from T0LD when Timer0 overflows.
T0LD, T0VAL, and T0CAP are 32-bit registers and hold
32-bit, unsigned integers of which T0VAL and T0CAP are
read only.
T0CLRI is an 8-bit register and writing any value to this
register clears the Timer0 interrupt.
T0CON is the configuration MMR, which is described in
Table 79.
32.768kHz OSCILLATOR
FREQUENCY/CD
CORE CLOCK
CORE CLOCK
FREQUENCY
GPIO
1, 16, 256, OR 32,768
IRQ[31:0]
PRESCALER
Figure 23. Timer0 Block Diagram
Rev. B | Page 66 of 108
CAPTURE
UP/DOWN COUNTER
32-BIT LOAD
32-BIT
Timer0 Load Registers
Name:
Address:
Default value:
Access:
Function:
Timer0 Clear Register
Name:
Address:
Access:
Function:
Timer0 Value Register
Name:
Address:
Default value:
Access:
Function:
TIMER0
VALUE
POSTSCALER
T0VAL
0xFFFF0324
0xFFFFFFFF
Read only
T0VAL is a 32-bit register that holds the
current value of Timer0.
T0LD
0xFFFF0320
0x00000000
Read and write
T0LD is a 32-bit register that holds the 32-bit
value that is loaded into the counter.
T0CLRI
0xFFFF032C
Write only
This 8-bit, write-only MMR is written
(with any value) by user code to clear the
interrupt.
8-BIT
TIMER0 IRQ